background image

     

Valve/pressure regulators are factory 

set to the correct operating pressures.  NO 

attempts should be made to adjust these 

settings.

Connecting the LP Gas Cylinder:

1. The valve on the LP cylinder must be closed. See 

that the knob is turned clockwise to a full stop.

2. Check that the control knob on the smoker is 

turned OFF.

3. Remove the protective cap from the LP Cylinder 

valve and coupling nut, if present.

4. Hold the regulator in one hand and insert the 

nipple into the valve outlet.  Be sure the nipple is 

centered in the valve outlet. The coupling nut 

connects to the large outside threads on the valve 

outlet, Use care - DO NOT cross thread the connec-

tion.

5. Hand tighten the coupling nut clockwise until it 

comes to a full stop.  Firmly tighten by hand only.  

DO NOT USE TOOLS.

CAUTION:

 In the connection process, the regula-

tor side of the connection will seal on the back check 

in the valve, resulting in a slight resistance.  The 

connection requires about one-half (1/2) to three-

quarters (3/4) additional turn to complete the 

connection.

When setting up the smoker and cylinder, it is recom-

mended to have the cylinder and the smoker on a line 

perpendicular to the wind direction.

The gas hose/regulator assembly should be totally 

extended to the maximum distance so that the hose 

is straight and the cylinder is as far from the smoker 

as it can be.

LP cylinders are intended for operation in the upright 

position only.

Care should be taken to protect the fuel supply hose 

from damage for either foot or vehicle traffic.

If the smoker is not in use, the gas must be turned 

off at the LP cylinder and the cylinder should be 

disconnected from the smoker and stored away from 

the smoker.

21

WARNING

CONNECTING THE LP CYLINDER 

- Continued

ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE 

FOLLOWED TO PREVENT FIRE, DAMAGE AND/OR INJURY.

Storage fo the smoker indoors is only permissible if 

the LP cylinder is disconnected and removed from 

the smoker.

LP cylinder must be stored outdoors out of reach of 

children and pets, and must not be stored in a 

building, garage or any other enclosed area.

Leak Testing (Check for gas leaks)

After all connections are completed, check all 

connections and fittings for leaks with a soap 

solution.

*  Mix dish soap with water (about 3:1 mix ratio)

*  With all valves closed, apply the soap solution to 

all gas flow connections and fittings.

* Open LP Cylinder valve about 1 -1/2 turn.

Presence of bubbles at areas of wet solution 

indicates a gas leak.

If leaks are detected or you smell or hear gas, shut 

off the value and repair the leak or replace the 

defective part.  DO NOT USE THE SMOKER UNTIL 

ALL LEAKS ARE CORRECTED.

DANGER

Summary of Contents for 3875GWLACR






























Reviews: