background image

- 2 - 

 

Please read before operating this system! 

 

 

e would like thank you for purchasing our new product—F9F-8 COUGAR, 
designed for the hobby enthusiast. Base on its full - scale counterpart, this USA Jet 
can finish loops, inverted flight and rolls and other aerobatics easily. Even the 
beginner can easily setup the model and fly it stably. It is also made as a highly 
maneuverable model for the intermediate to expert pilot. With the F9F-8 COUGAR 
model which includes EDF set*, speed controller, electric servo and retract landing 
gear with front steering (Gear doors system is an optional requirement) you will 
have joyful time in model flying. 

 

Remarks:* 

We have two types EDF set (4S & 6S version) for your selection. 

 

1) EDF68-1A is a higher grade EDF set which is an aluminum alloy material EDF 

more powerful output, efficient and durability. 

2) Please be noticed that all servos have been pre-set the center point before out 

of factory. It maybe appeared some difference due to difference brand name radio 
control. Kindly make sure to do the adjustment 

(special to pre-set the travel of 

gear servo up to 130 %. If you select gear doors system with special 
modified travel throw servos. You are needed to pre-set the travel of gear 
servo up to 110-120%)

 with your own radio equipment before installation this jet 

model. 

3) Centre of Gravity for this model is measured 80mm from main wing leading 

edge. 

4) Please make sure to use a little piece of attached velco to secure your LiPo 

battery before flying. 

 

 

 

 

 

 

Summary of Contents for F9F - 8 Cougar














Reviews: