background image

11

Operations

Operating Instructions

STEP 1:

 Read engine warning and 

operating instructions prior to 
turning on the water. Check for 
water leaks; tighten as needed.

STEP 3:

 With the spray nozzle 

pointed away from you or anybody 
else, press the trigger on the spray 
gun to obtain pressurized cold 
water spray.

STEP 4:

 For hot water, turn the 

thermostat knob to 210° then push 
the burner switch to ON when a 
steady stream of water flows out of 
the spray gun. Burner will now light 
automatically. 

NOTE:

 Do not start 

machine with burner switch on.

STEP 6:

 The four color-coded 

quick connect nozzles provide a 
wide array of spray widths from 0° 
to 45° and are easily accessible 
when placed in the convenient 
rubber nozzle holder, which is 
provided on the front of the 
machine. 

NOTE:

 For a more gentle rinse, 

select the white 40° or green 25° 
nozzle. To scour the surface, select 
the yellow 15° or red 0° nozzle. 

CAUTION: When using the 0° 
nozzle to prevent surface and 
injection damage and injury.

ATTENTION: En utilisant la buse 
1° pour prévenir les dommages à 
la surface et à l'injection, et les 
blessures.

STEP 2:

 Read engine manual 

provided and pull choke. Pull spray 
gun trigger to relieve pressure. 
Then turn the engine switch to the 
START position and hold it there 
until the engine starts. 

 NOTE

: Do 

not engage the electric starter for 
more than five (5) seconds at a 
time. If the engine fails to start, 
release the switch, pull spray gun 
trigger and wait ten seconds before 
operating the starter again. When 
the engine starts, allow the engine 
switch to return to the ON position. 
Push the choke in.

STEP 5:

 For steam, open the 

steam valve counterclockwise. This 
lowers the pressure and raises the 
temperature.

Landa SLT/SLX Gas Operator’s Manual  8.914-002.0 - AR

Choke

Keyhole

Ne

ver Use:

·

Bleach, chlo

rine products and other corrosiv

e chemical

s

·

Liquid

s containin

g solv

ents (i.e

. paint thinner

, gasoline

, oil)

·

  T

ri-sodium p

hosphate products

·

  Ammonia p

roducts

·

  Acid-based products

These chemicals will 

har

m the

 unit and 

will damage 

the 

surf

ace being cleaned.

 

Use manu

facturer’

s deterge

nts as recommended i

n manual

.

CA

UTION

Steam Valve

Burner 
Switch

Thermostat 

Knob

Nozzles

Summary of Contents for SLT6-32324E 1.110-520.0























Reviews: