background image

LANDA SEHW  •  8.913-932.0   •  Rev. 02/12a

OPERA

TOR’S MANU

AL

  

PRESSURE 

W

ASHER 

 

4

RISK OF INJECTION 

OR SEVERE INJURY 

TO PERSONS. KEEP 

CLEAR OF NOZZLE.

WARNING

WARNING: High pressure devel-

oped  by  these  machines  will 
cause personal injury or equip-
ment  damage.  Keep  clear  of 
nozzle. Use caution when oper-
ating.  Do  not  direct  discharge 
stream at people, or severe in-
jury or death will result. 

 

WARNING

PROTECT FROM 

FREEZING

WARNING: Protect machine from 

freezing.

15.  To  keep  machine  in  best  
 

operating  conditions,  it  is  

 

important you protect machine  

 

from freezing. Failure to protect  

 

m a c h i n e   f r o m   f r e e z i n g  

 

could cause malfunction of the  

 

machine and result in death, 

serious bodily injury, and/or property damage. Fol-
low storage instructions specified in this manual.

16. Inlet water must be clean fresh water and no hotter 

then 90°F.

 

WARNING

RISK OF 

ASPHYXIATION. USE 

THIS PRODUCT ONLY 

IN A WELL 

VENTILATED AREA.

WARNING: Risk of asphyxiation. 

Use  this  product  only  in  a  well 
ventilated area. 
 17.  Avoid  installing  machines  in 

small  areas  or  near  exhaust 
fans.  Adequate  oxygen  is 
needed  for  combustion  or 
dangerous  carbon  monoxide 
will result.

 18.  Manufacturer  will  not  be  liable  for  any  changes 

made to our standard machines or any components 
not purchased from us.

 19.  The best insurance against an accident is precau-

tion and knowledge of the machine.

WARNING

RISK OF INJURY 

FROM FALLS WHEN 

USING LADDER.

WARNING: Be extremely careful 

when using a ladder, scaffolding 
or any other relatively unstable 
location. The  cleaning  area 
should  have  adequate  slopes 
and drainage to reduce the pos-
sibility of a fall due to slippery 
surfaces.
 

 20.  Do  not  overreach  or  stand  on  unstable  support. 

Keep good footing and balance at all times.

 21.  Do not operate this machine when fatigued or under 

the influence of alcohol, prescription medications,  
or drugs.

IMPORTANT SAFETY INFORMATION

WARNING

USE PROTECTIVE  

EYE WEAR 

AND CLOTHING  

WHEN OPERATING 

THIS EQUIPMENT.

WARNING: High pressure spray 

can cause paint chips or other 
particles  to  become  airborne 
and fly at high speeds. To avoid 
personal  injury,  eye,  hand  and 
foot  safety  devices  must  be 
worn.
 11.   Eye, hand, and foot protection 

must be worn when using this 
equipment.

WARNING

EAR PROTECTION 

MUST BE WORN

WARNING: This machine exceeds 

85 db appropriate ear protection 
must be worn.

 

WARNING

HOT DISCHARGE FLUID: 

DO NOT TOUCH OR 

DIRECT DISCHARGE 

STREAM AT PERSONS.

WARNING: Hot discharge fluid. 
Do not touch or direct discharge 
stream at persons.
WARNING: This  machine  pro-
duces hot water and must have 
insulated components attached 
to protect the operator.

WARNING

RISK OF INJURY.  

HOT SURFACES  

CAN CAUSE BURNS

WARNING:  Risk  of  injury.  Hot 

surfaces can cause burns. Use 
only designated gripping areas 
of spray gun and wand. Do not 
place hands or feet on non-insu-
lated  areas  of  the  pressure 
washer.

 

 12.  To  reduce  the  risk  of  injury,  close  supervision  is 

necessary when a machine is used near children. 
Do  not  allow  children  to  operate  the  pressure 
washer. 

This machine must be attended during 

operation. 

 

TRIGGER GUN KICKS 

BACK - HOLD WITH  

BOTH HANDS

WARNING

WARNING: Grip cleaning wand 

securely with both hands before 
starting. Failure to do this could 
result in injury from a whipping 
wand.
13.   Never  make  adjustments  on 

machine while in operation. 

 14.  Be certain all quick coupler fit-

tings are secured before using 
pressure washer.

Summary of Contents for SEHW6-3500







































Reviews: