background image

6

Safety

WARNING: Keep wand, hose, and 
water spray away from electric 
wiring or fatal electric shock may 
result.

AVERTISSEMENT: Garder la lance, 
le boyau et le jet d'eau à l'écart de 
tout câblage électrique ou des 
chocs électriques mortels 
pourraient survenir.

5. To protect the operator from electrical shock, the 

machine must be electrically grounded. It is the 
responsibility of the owner to connect this machine to 
a UL grounded receptacle of proper voltage and 
amperage ratings. Do not spray water on or near 
electrical components. Do not touch machine with wet 
hands or while standing in water. Always disconnect 
power before servicing.

WARNING: Flammable liquids can 
create fumes which can ignite, 
causing property damage or severe 
injury.

AVERTISSEMENT: Des liquides 
inflammables peuvent produire des 
vapeurs qui peuvent s'enflammer, 
causant ainsi des dommages à la 
propriété ou des blessures graves.

WARNING: Risk of explosion — Operate only where 
open flame or torch is permitted.
AVERTISSEMENT: Risque d'explosion- Utiliser 
uniquement dans des endroits où l'utilisation d'une 
flamme nue ou d'une torche est permise.

6. In oil burning models, use only kerosene, No. 1 home 

heating fuel, or diesel. If diesel is used, add a soot 
remover to every tankful.

WARNING: Risk of fire — Do not 
add fuel when the product is 
operating or still hot. 
AVERTISSEMENT: Risque 
d'incendie- Ne pas ajouter de 
carburant pendant que la machine 
fonctionner ou est encore chaude.
WARNING: Do not use gasoline 
crankcase drainings or oil 
containing gasoline, solvents or 

alcohol. Doing so will result in fire and/or explosion.

AVERTISSEMENT: Ne pas utiliser d'essence, de 
drainage du carter de moteur ou d'essence contenant 
de l'huile, de solvants ou de l'alcool.

7. This pressure washer shall be installed only in 

locations where combustible dusts and flammable 

gases or vapors are not present. Do not store or use 
gasoline near this machine.

8. Do not allow acids, caustic or abrasive fluids to pass 

through the pump.

9. Never run pump dry or leave spray gun closed longer 

than 1-2 minutes.

10. Keep operating area clear of all persons and animals.

WARNING: High pressure spray can 
cause paint chips or other particles 
to become airborne and fly at high 
speeds. To avoid personal injury, 
eye, face, hand and foot safety 
devices must be worn.

AVERTISSEMENT: Un jet haute 
pression peut écailler la peinture 
ou provoquer l'émission d'autres 
particules dans l'air et leur 

projection à hautes vitesses. Pour éviter les lésions 
corporelles, une protection des yeux, du visage, des 
mains et des pieds doit être portée lors de l'utilisation 
de cet équipement.

11. Always wear properly rated eye protection such as 

safety goggles or face shield while spraying. 

(Safety 

glasses do not provide full protection.) 

WARNING: Hot discharge fluid. Do 
not touch or direct discharge 
stream at persons or animals or 
severe injury or death will result.

AVERTISSEMENT: Liquide de 
décharge chaud. Ne pas toucher ou 
décharger directement le jet vers 
des personnes ou des animaux, car 
cela risquerait de causer des 
blessures graves ou même la mort.

WARNING: This machine produces hot water and 
must have insulated components attached to protect 
the operator.

AVERTISSEMENT: Cette machine produit de l'eau 
chaude et doit comporter des composants isolés 
attachés pour protéger l'opérateur.

WARNING: Risk of injury. Hot 
surfaces can cause burns. Use only 
designated gripping areas of spray 
gun and wand. Do not place hands 
or feet on non-insulated areas of 
the pressure washer.

AVERTISSEMENT: Risque de 
blessures. Les surfaces chaudes 
peuvent causer des brûlures. 
Utiliser uniquement les zones de 

Landa HOT Series Operator’s Manual  8.917-208.0 - B

WARNING

    USE PROTECTIVE 

  EYE WEAR 

AND CLOTHING

WHEN OPERATING

 THIS EQUIPMENT.

       

KEEP WATER 

 SPRAY AWAY FROM 

ELECTRICAL WIRING.

WARNING

WARNING

RISK OF EXPLOSION: 

OPERATE ONLY WHERE 

OPEN FLAME OR TORCH 

IS PERMITTED

WARNING

RISK OF FIRE. 

DO NOT ADD FUEL 

WHEN OPERATING

MACHINE.

WARNING

HOT DISCHARGE FLUID:

DO NOT TOUCH OR

DIRECT DISCHARGE

STEAM AT PERSONS.

WARNING

RISK OF INJURY. 

HOT SURFACES 

CAN CAUSE BURNS

Summary of Contents for 1.109-093.0























Reviews: