Land Pride RCP2560 Series Page 4 Operator'S Manual Download

Page: 4 / 38

Important Safety Information

RCP2560 & RCPM2560 Series Parallel Arm Rotary Cutter 316-057M

4/28/08

Land Pride

Table of Contents

Transport
Machinery Safely

▲

Comply with state and local laws.

▲

Maximum transport speed for

implement is 20 mph. DO NOT
EXCEED. Never travel at a speed
which does not allow adequate
control of steering and stopping.
Some rough terrain require a
slower speed.

▲

Sudden braking can cause a

towed load to swerve and upset.
Reduce speed if towed load is not
equipped with brakes.

▲

Use

the

following

maximum

speed - tow load weight ratios as
a guideline:

20 mph when weight is less
than or equal to the weight of
tractor.
10 mph when weight is double
the weight of tractor.

IMPORTANT: Do not tow a load that

is more than double the weight of
tractor.

Use Safety
Lights and Devices

▲

Slow moving tractors, self-

propelled equipment, and towed
implements can create a hazard
when driven on public roads. They
are difficult to see, especially at
night.

▲

Flashing warning lights and turn

signals are recommended
whenever driving on public roads.
Use lights and devices provided
with implement.

Practice Safe Maintenance

▲

Understand procedure before

doing work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.

▲

Work in a clean dry area.

▲

Lower the implement to the

ground, put tractor in park, turn off
engine, and remove key before
performing maintenance.

▲

Allow implement to cool

completely.

▲

Do not grease or oil implement

while it is in operation.

▲

Inspect all parts. Make sure parts

are in good condition & installed
properly.

▲

Remove buildup of grease, oil or

debris.

▲

Remove all tools and unused

parts from implement before

Use A Safety Chain

▲

A safety chain will help control

drawn machinery should it
separate from the tractor
drawbar.

▲

Use a chain with the strength

rating equal to or greater than
the gross weight of the towed
machinery.

▲

Attach the chain to the tractor

drawbar support or other
specified anchor location. Allow
only enough slack in the chain to
permit turning.

▲

Do not use safety chain for

towing.

Summary of Contents for RCP2560 Series







































Search results

Summary of Contents for RCP2560 Series

Reviews:

Related manuals for RCP2560 Series

Brands by name

Popular brands

Land Pride RCP2560 Series, Operator'S Manual

Search results

Summary of Contents for RCP2560 Series

Reviews:

Related manuals for RCP2560 Series

Brands by name

Popular brands