Land Pride RCP2560 Series Operator'S Manual Download | Manualshive

Page: 2 / 38

background image

Table of Contents

RCP2560 & RCPM2560 Series Parallel Arm Rotary Cutter 316-057M

4/28/08

Land Pride

Table of Contents

©

Copyright 2008 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land
Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves
the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Important Safety Information . . . . . . . . . . .1

Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Section 1: Introduction . . . . . . . . . . . . . . .8

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 8

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 8

Serial Number Plate . . . . . . . . . . . . . . . . . . . . . 8
Further Assistance . . . . . . . . . . . . . . . . . . . . . . 8

Section 2: Assembly & Set-up . . . . . . . . . .9

Tractor Requirements  . . . . . . . . . . . . . . . . . . . . . . 9
Preparation Checklist . . . . . . . . . . . . . . . . . . . . . . 10
Dealer Preparations . . . . . . . . . . . . . . . . . . . . . . . 10
3-Point Hookup  . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PTO Hookup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Hydraulic Hookup  . . . . . . . . . . . . . . . . . . . . . . . . 13
Electrical Hookup . . . . . . . . . . . . . . . . . . . . . . . . . 14
Functional Check . . . . . . . . . . . . . . . . . . . . . . . . . 15
Operator Protective Shield . . . . . . . . . . . . . . . . . . 16
Setting Flow Control Valve . . . . . . . . . . . . . . . . . . 17

Section 3: Hydraulics . . . . . . . . . . . . . . . .18

Hydraulic Cylinder Plumbing . . . . . . . . . . . . . . . . 18
Marking Hydraulic Line Lengths . . . . . . . . . . . . . . 19

Section 4: Adjustments . . . . . . . . . . . . . .22

Deck Level Adjustments . . . . . . . . . . . . . . . . . . . 22

Section 5: Transporting . . . . . . . . . . . . . .23

Section 6: Operating Procedures . . . . . .24

Breakaway Operations . . . . . . . . . . . . . . . . . . . . . 24
Tension Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Breakaway Cylinder . . . . . . . . . . . . . . . . . . . . . . . 25
General Operating Instructions . . . . . . . . . . . . . . 26

Section 7: Maintenance & Lubrication . .27

Lubrication Points . . . . . . . . . . . . . . . . . . . . . . . . 27

Parallel Arm Cutter Zerks . . . . . . . . . . . . . . . . 27
PTO Zerks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Driveline Profiles . . . . . . . . . . . . . . . . . . . . . . . 27

Blade Servicing (Replacement)  . . . . . . . . . . . . . . 28
Tractor Maintenance  . . . . . . . . . . . . . . . . . . . . . . 29
Storage  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Section 8: Specifications & Capacities . .31

Section 9: Troubleshooting . . . . . . . . . . .33

Section 10: Appendix . . . . . . . . . . . . . . . .34

Torque Values Chart . . . . . . . . . . . . . . . . . . . . . . 34
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table of Contents

«
1
2
3
4
...
»

Summary of Contents for RCP2560 Series







































Reviews:

No comments

Related manuals for RCP2560 Series

Brand: Makita Pages: 110

Brand: Makita Pages: 2

Brand: Makita Pages: 14

Brand: Makita Pages: 26

Brand: D-CUT Pages: 6

Brand: Zipper Mowers Pages: 48

Brand: PARKEN ENGINEERING Pages: 6

Brand: CNC-Step Pages: 115

Brand: Hitachi Koki Pages: 26

Brand: Okay Pages: 56

Brand: Velleman Pages: 4

Brand: Norge Pages: 21

MS-3310, MS-4010, MS-4510

Brand: Dolmar Pages: 74

Brand: Dolmar Pages: 92

Brand: Becx Machines Pages: 27

Brand: Epilog Pages: 32

Brand: YATO Pages: 116

Brand: Kaltenbach Pages: 268

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands