background image

Important Safety Information

8/22/23

1

Important Safety Information

Listed below are common practices that may or may not be applicable to the products 
described in this manual.

Tractor Shutdown & Storage

If engaged, disengage power 
take-off.

Park on solid, level ground and 
lower implement to ground or onto 
support blocks.

Put tractor in park or set park 
brake.

Turn off engine and remove 
ignition key to prevent 
unauthorized starting.

Relieve all hydraulic pressure to 
auxiliary hydraulic lines. 

Wait for all components to stop 
before leaving operator’s seat.

Use steps, grab-handles and 
anti-slip surfaces when stepping 
on and off the tractor.

OFF

REMOVE

Look for the Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a potential hazard 
to personal safety and extra precaution must be taken. When you 
see this symbol, be alert and carefully read the message that 
follows it. Hazard control, and accident prevention are dependent 
upon the awareness, concern, prudence, and proper training of 
personnel involved in the operation, transport, maintenance, and 
storage of equipment.

Safety Precautions for 
Children

Tragedy can occur if the operator 
is not alert to the presence of 
children, Children generally are 
attracted to implements and their 
work.

Never assume children will remain 
where you last saw them.

Keep children out of the work area 
and under the watchful eye of a 
responsible adult.

Be alert and shut the implement 
and tractor down if children enter 
the work area.

Never carry children on the tractor 
or implement. There is not a safe 
place for them to ride. They may 
fall off and be run over or interfere 
with the control of the power 
machine.

Never allow children to operate the 
power machine, even under adult 
supervision.

Never allow children to play on the 
power machine or implement.

Use extra caution when backing 
up. Before the tractor starts to 
move, look down and behind to 
make sure the area is clear.

Safety at All Times

Careful operation is your best 
assurance against an accident. 

All operators, no matter how much 
experience they may have, should 
carefully read this manual and 
other related manuals before 
operating the power machine and 
this implement. 

Thoroughly read and understand 
the “Safety Label” section. Read 
all instructions noted on them.

Do not operate the equipment 
while under the influence of drugs 
or alcohol, as they impair your 
ability to safely and properly 
operate the equipment.

The operator should be familiar 
with all functions of the tractor and 
attached implement, and be able 
to handle emergencies quickly.

Make sure all guards and shields 
appropriate for the operation are in 
place and secured before 
operating the implement.

Keep all bystanders away from 
equipment and work area. 

Start tractor from the driver’s seat 
with hydraulic controls in neutral.

Operate tractor and controls from 
the driver’s seat only.

Never dismount from a moving 
tractor or leave tractor unattended 
with engine running.

Do not allow anyone to stand 
between the implement and 
tractor while backing up to the 
implement.

Keep hands, feet, and clothing 
away from power-driven parts.

While transporting and operating 
equipment, watch out for objects 
overhead and along the sides 
such as fences, trees, buildings, 
wires, etc. 

Do not turn tractor so tight as to 
cause hitched implement to ride 
up on the tractor’s rear wheel.

Store implement in a safe and 
secure area where children 
normally do not play. When 
needed, secure implement against 
falling with support blocks.

!

Be Aware of Signal Words

A signal word designates a degree or level of hazard seriousness. They are:

DANGER:

!

WARNING:

CAUTION:

!

!

Indicates a hazardous situation that, if not avoided, will result 
in death or serious injury. 

Indicates a hazardous situation that, if not avoided, could 
result in death or serious injury.

Indicates a hazardous situation that, if not avoided, may result 
in minor or moderate injury.

Be Aware of Special Notices

Special notices are intended to point out important and helpful information that 
should be followed. They are usually placed inside a box. They are:

Indicates that equipment or property damage could result if 
instructions are not followed.

Indicates supplementary explanations that will be helpful when 
using the equipment.

IMPORTANT:

NOTE:

Summary of Contents for RC4615





































































Reviews: