Land Pride RB16 Series Operator'S Manual Download Page 7

Important Safety Information

9/28/18

3

Listed below are common practices that may or may not be applicable to the products 
described in this manual.

Avoid High 
Pressure Fluids Hazard

Escaping fluid under pressure can 
penetrate the skin causing serious 
injury.

Before disconnecting hydraulic 
lines or performing work on the 
hydraulic system, be sure to 
release all residual pressure.

Make sure all hydraulic fluid 
connections are tight and all 
hydraulic hoses and lines are in 
good condition before applying 
pressure to the system.

Use a piece of paper or 
cardboard, NOT BODY PARTS, to 
check for suspected leaks.

Wear protective gloves and safety 
glasses or goggles when working 
with hydraulic systems.

DO NOT DELAY.

 If an accident 

occurs, see a doctor familiar with 
this type of injury immediately. Any 
fluid injected into the skin or eyes 
must be treated within 
a few hours or 
gangrene may 
result.

Wear Personal Protective 
Equipment (PPE)

Wear protective clothing and 
equipment appropriate for the job 
such as safety shoes, safety 
glasses, hard hat, and ear plugs.

Clothing should fit snug without 
fringes and pull strings to avoid 
entanglement with moving parts.

Prolonged exposure to loud noise 
can cause hearing impairment or 
hearing loss. Wear suitable 
hearing protection such as 
earmuffs or earplugs.

Operating equipment safely 
requires the operator’s full 
attention. Avoid  wearing 
headphones while operating 
equipment.

Use Seat Belt and ROPS

Land Pride recommends the use 
of a CAB or roll-over-protective-
structures (ROPS) and seat belt 
in almost all power machines. 
Combination of a CAB or ROPS 
and seat belt will reduce the risk 
of serious injury or death if the 
power machine should be upset.

If ROPS is in the locked-up 
position, fasten seat belt snugly 
and securely to help protect 
against serious injury or death 
from falling and machine overturn.

Keep Riders Off 
Machinery

Never carry riders on tractor or 
implement.

Riders obstruct operator’s view 
and interfere with the control of 
the power machine. 

Riders can be struck by objects or 
thrown from the equipment.

Never use tractor or implement to 
lift or transport riders.

Avoid Underground 
Utilities

Dig Safe, Call 811 (USA).

Always contact your local utility 
companies (electrical, telephone, 
gas, water, sewer, and others) 
before digging so that they may 
mark the location of any 
underground services in the area. 

Be sure to ask how close you can 
work to the marks they positioned.

Prepare for Emergencies

Be prepared if a fire starts.

Keep a first aid kit and fire 
extinguisher handy.

Keep emergency numbers for 
doctor, ambulance, hospital, and 
fire department near phone.

911

Use Safety 
Lights and Devices

Slow moving tractors, skid steers, 
self-propelled machines, and towed 
equipment can create a hazard 
when driven on public roads. They 
are difficult to see, especially at 
night. Use the Slow Moving Vehicle 
sign (SMV) when on public roads.

Flashing warning lights and turn 
signals are recommended 
whenever driving on public roads.

Summary of Contents for RB16 Series

































Reviews: