![background image](http://html1.mh-extra.com/html/land-pride/os1548/os1548_operators-manual_3523864023.webp)
Section 2: Operating Instructions
OS1548 and OS1572 Overseeder (S/N ) 308-303M
11/28/18
19
Section 2: Operating Instructions
Operating Checklist
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance of the seeder. Therefore, it is absolutely
essential that no one operates the Overseeder without
first having read, fully understood, and become totally
familiar with the Operator’s Manual. Make sure the
operator has paid particular attention to:
•
Important Safety Information
, page 1
•
•
Section 2: Operating Instructions
•
•
Section 4: Maintenance & Lubrication
The following information should be known and
inspections made before operating your seeder.
Operating Checklist
Check
Page No.
Read and follow all safety rules & alerts carefully.
Refer to “Important Safety Information”.
Page 1
Make sure all guards and shields are in place.
Refer to “Important Safety Information”.
Page 1
Read and follow all operating procedures.
Refer to “Section 2: Operating Instructions”.
Read and make all required adjustments.
Refer to “Section 3: Adjustments”.
Read and follow all maintenance instructions.
Refer to “Section 4: Maintenance & Lubrication”.
Read and follow all lubrication instructions.
Refer to “Lubrication Points”.
Make sure all gearboxes are properly lubricated.
Refer to Gearbox lubrication.
Check tire pressure. See to
Inspect seed cups and seed tubes for foreign
matter.td
Set speed change sprocket for drive type
desired.
Set seed rate. See “
Seed Rate Charts
”.
Check seeder initially and periodically for loose
bolts and pins. Refer to “Torque Values Chart”.
Transporting
WARNING
!
To avoid serious injury or death:
•
Select a safe ground speed when transporting. Never travel
at a speed which does not allow adequate control of steering
and stopping, and never exceed 20 mph (32.2 km/h) with
attached equipment. Rough terrain requires a slower speed.
•
When traveling on public roads, use LED lights, slow
moving vehicle sign, clean reflectors, and other adequate
devices to warn operators in other vehicles of your
presence. If implement blocks visibility of slow moving
vehicle sign, relocate sign so it is visible from the back at all
times. Always comply with all federal, state, and local laws.
•
Reduce ground speed when turning and leave enough
clearance to avoid making contact with obstacles such as
buildings, trees, fences, etc. Making contact can result in
equipment damage and cause serious injury or death.
•
Slow down when traveling over rough or hilly terrain. Shift
to a lower gear to maintain engine rpm while traveling
•
Slow down when traveling over rough or hilly terrain that
can cause equipment to bounce, or to hit obstacles that are
close by. Either situation can cause damage and/or the
1.
Relocate slow moving vehicle Safety sign from back
of your tractor to the slow moving vehicle mounting
bracket (#6) on the back of the seeder. If needed, a
slow moving vehicle sign can be purchased from
your nearest Land Pride dealer. Refer to
1.
This seeder can be transported with a full box of
seed, however; it is best not to do this unless
necessary because the increased weight does
increase the chances for problems on the road.
2. Select a safe ground travel speed when transporting
from one area to another. Do not exceed 20 miles per
hour travel speed.
3. When traveling on roadways, transport in such a way
that faster moving vehicles may pass you safely.
4. Reduce tractor ground speed when turning. Leave
enough clearance so the seeder does not contact
obstacles such as buildings, trees, or fences.
5. Shift tractor to a lower gear when traveling over rough
or hilly terrain.
IMPORTANT:
The slow moving vehicle sign should
not be used when transporting equipment on a truck
or trailer exceeding seeds of 25 mph. Cover or
remove the slow moving vehicle sign when hauling
the Overseeder.