background image

Section 4: Adjustments 

Table of Contents

LR0548 and LR0560 Landscape Rakes 302-185M

11/5/18

13

Section 4: Adjustments

Safety Alerts

WARNING

!

To avoid serious injury or death:  

Avoid injury from a falling rake. Always check to make sure 

all hardware is secured before adjusting the rake.

Do not make contact with the turntable or stick objects into 

the turntable holes while adjusting the unit’s angle and/or 

offset. Doing so can pinch or shear body extremities and/or 

objects.

Never fully extend or retract hydraulic cylinder(s) without 

first checking to make sure the implement does not make 

contact with tractor tires. Extending implement into the 

tractor tires can result in loss of control and damage to the 

implement and/or tractor.

Rake Angling

Refer to Figure 4-1:

The Landscape Rake can be angled horizontally up to 
30

o

 in 15

o

 increments right and left.

1.

Read and follow all 

“Safety Alerts”

 above.

2. Pull bent pin (#2) from hole in mainframe. 

3. Rotate rake (#1) to the desired angle and reinsert 

bent pin (#1). 

Rake Angling

Figure 4-1

IMPORTANT:  

The implement must be hitched to a 

tractor and raised off the ground several inches to 
make the following adjustments.

35324

Rake Pitch

The rake pitch (angle the rake teeth enter the ground) 
may be adjusted to increase or decrease the rake’s ability 
to dig into the soil.

1.

Read and follow all 

“Safety Alerts” 

on this page.

2. Lengthening tractor’s top center 3-Point link 

increases rake pitch making the rake more 
aggressive on the soil.

3. Shortening tractor’s top center 3-Point link decreases 

rake pitch making the rake less aggressive on the 
soil.

Rake Tilt

The rake may be tilted so one end is lower than the other.

1.

Read and follow all 

“Safety Alerts” 

on this page.

2. Adjust one or both of the tractor’s lower 3-Point arms 

up or down. Also refer to the tractor’s manual for 
instructions to adjust the lower 3-Point arms.

Gauge Wheels (Optional)

Refer to Figure 4-2:

1.

On the right side, remove linchpin (#3) from yoke 
shaft (#1). 

2. Remove gauge wheel (#1) from support arm (#2). 

3. Place desired number of spacers (#4 & #5) on yoke 

shaft (#1). 

4. Reinsert gauge wheel assembly (#1) into support 

arm (#2). 

5. Place remaining spacers (#4 & #5) on yoke shaft (#1) 

above support arm (#2) and reattach linchpin (#3).

6. Repeat steps 1-5 for the left side.

Rake Angling

Figure 4-2

35325

Summary of Contents for LR0548

























Reviews: