background image

Section 1: Assembly & Set-Up 

GB2084 Grapple Bucket 380-328M

3/17/20

9

Table of Contents

Tractor Shutdown Procedure

The following are basic tractor shutdown procedures. 

Follow these procedures and any additional shutdown 

procedures provided in your tractor Operator’s Manual 

before leaving the operator’s seat.
1. Reduce engine speed and shut-off all power to the 

attachment. 

2. Park tractor and attachment on solid, level ground.
3. Lower attachment until it is flat on the ground or on 

non-concrete support blocks. 

4. Put tractor in park or set park brake, turn off engine, 

and remove switch key to prevent unauthorized 

starting.

5. Relieve all hydraulic pressure to auxiliary hydraulic 

lines.

6. Wait for all components to come to a complete stop 

before leaving the operator’s seat.

7.

Use steps, grab-handles and anti-slip surfaces when 

stepping on and off the tractor.

Pre-Assembly Checklist

Check

Ref.

Have a hoist, forklift, or loader with properly sized chains and 
safety stands capable of lifting and supporting the equipment 
on hand.

Have a minimum of two people available during assembly.

Make sure all safety labels are correctly located 
and legible. Replace if damaged.

Page 6

Make sure all major components and loose 
parts are shipped with the machine.

Page 9

Double check to make sure all parts, fasteners, 
and pins are installed in the correct location. 
Refer to the Parts Manual if unsure. 

NOTE:

 All assembled hardware from the factory 

has been installed in the correct location. 
Remember location of a part or fastener if 
removed. Keep parts separated.

Operator’s 
Manual 
380-328M

Parts Manual 
380-328P

Make sure working parts move freely, bolts are 
tight & cotter pins are spread.

Operator’s
Manual

Make sure all grease fittings are in place and 
lubricated.

Page 26

Section 1: Assembly & Set-Up

Tractor Requirements

Tractor horsepower should be within the range noted 

below. Tractors outside the horsepower range must not 

be used.

Horsepower Rating  . . M5 or M6 tractors up to 135 Hp
Hitch Type: . . . . . . . Skid steer type quick attach hitch
Hydraulic Outlets . . . . . . . . . . . . . . . . . . . . .  1 Duplex
Tractor Weight  . . . . . . . . . . . . . . See Warnings Below

WARNING

!

To avoid serious injury or death:  

Consult your power machine Operator’s Manual for 

operating capacity, lifting capacity, and operating 

specifications. Exceeding rated capacities and 

specifications can result in a roll-over or other serious 

hazard.

Use a power machine of adequate size for the load being 

carried. An undersized machine can roll over when raising 

the loader arms due to high center of gravity.

Lightweight power machines may need weight added to the 

rear to maintain steering control and prevent forward 

tipping or side tipping caused by a heavy front load. Consult 

your power machine Operator’s Manual to determine 

proper weight requirements and maximum weight 

limitations.

Torque Requirements

Refer to 

“Torque Values Chart” 

on page 30 to determine 

correct torque values when tightening hardware.

Before You Start

Make sure the intended tractor conforms to the tractor 

requirements provided on this page. Also, read and 

understand this Operator’s Manual for your Grapple 

Bucket. An understanding of how it works will aid in its 

assembly and set-up. 
Go through the 

“Pre-Assembly Checklist” 

on this page 

before assembling the Grapple Bucket. To speed up your 

assembly task and make the job safer, have all needed 

parts and equipment readily at hand.

Summary of Contents for GB2084





































Reviews: