background image

Important Safety Information

12/7/18

1

Important Safety Information

Listed below are common practices that may or may not be applicable to the products 
described in this manual.

Safety at All Times

Careful operation is your best 
assurance against an accident. 

All operators, no matter how much 
experience they may have, should 
carefully read this manual and 
other related manuals, or have the 
manuals read to them, before 
operating the power machine and 
this attachment. 

Thoroughly read and understand 
the “Safety Label” section. Read 
all instructions noted on them.

Do not operate the equipment 
while under the influence of drugs 
or alcohol as they impair the ability 
to safely and properly operate the 
equipment.

Operator should be familiar with all 
functions of the tractor/skid steer 
and attachment and be able to 
handle emergencies quickly.

Make sure all guards and shields 
appropriate for the operation are in 
place and secured before 
operating attachment.

Keep all bystanders away from 
equipment and work area.

Start tractor/skid steer from the 
driver’s seat with steering levers 
and hydraulic controls in neutral.

Operate tractor/skid steer and 
controls from the driver’s seat only.

Never dismount from a moving 
tractor/skid steer or leave machine 
unattended with engine running.

Do not allow anyone to stand 
between tractor/skid steer and 
attachment while hooking-up.

Keep hands, feet, and clothing 
away from power-driven parts.

While transporting and operating 
equipment, watch out for objects 
overhead and along side such as 
fences, trees, buildings, wires, etc. 

Store attachment in an area where 
children normally do not play. 
When needed, secure attachment 
against falling with support blocks.

Look for the Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a 
potential hazard to personal safety involved and extra 
safety precaution must be taken. When you see this 
symbol, be alert and carefully read the message that 
follows it. In addition to design and configuration of 
equipment, hazard control, and accident prevention are 
dependent upon the awareness, concern, prudence, and 
proper training of personnel involved in the operation, 
transport, maintenance, and storage of equipment.

OFF

REMO

VE

Skid Steer Shutdown 
And Storage

Reduce engine speed and shut-off 
all power to the attachment. 

Park on solid, level ground and 
lower attachment until it is flat on 
the ground or support blocks. 

Turn off engine, and remove 
switch key to prevent unauthorized 
starting.

Relieve all hydraulic pressures. 

If included, raise seat bar and 
move controls until both lock. 

Wait for all components to stop 
before leaving operator’s seat.

Use steps, grab-handles and 
anti-slip surfaces when stepping 
on and off the skid steer.

Detach and store attachment in an 
area where children normally do 
not play. Secure attachment by 
using blocks and supports.

Tractor Shutdown & Storage

Reduce engine speed and shut-off 
all power to the attachment. 

Park on solid, level ground and 
lower attachment to ground or 
onto support blocks.

Put tractor in park or set park 
brake, turn off engine, and remove 
switch key to prevent unauthorized 
starting.

Relieve all hydraulic pressures. 

Wait for all components to stop 
before leaving operator’s seat.

Use steps, grab-handles and 
anti-slip surfaces when stepping 
on and off the tractor.

Detach and store implement in an 
area where children normally do 
not play. Secure implement using 
blocks and supports.

OFF

REMO

VE

Be Aware of 
Signal Words

A signal word designates a degree or 
level of hazard seriousness. The 
signal words are:

Indicates a hazardous situation that, if 
not avoided, will result in death or 
serious injury. 

Indicates a hazardous situation that, if 
not avoided, could result in death or 
serious injury.

Indicates a hazardous situation that, if 
not avoided, may result in minor or 
moderate injury.

WARNING

CAUTION

!

!

!

DANGER

!

Summary of Contents for BS30































Reviews: