background image

Section 1: Assembly & Set-up 

Table of Contents

 BB3578, BB3584, & BB3596 Fixed Bar Box Scraper 303-398M

11/7/18

6

Hitch & Shank Assembly (Shanks Not Shown For Clarity)

Figure 1-1

39253

Section 1: Assembly & Set-up

Hitch Assembly

Refer to Figure 1-1:

1.

Attach left-hand hitch plate (#1) to the inside of clevis 
plate “A” with 3/4”-10 x 2” GR5 bolts (#4), lock 
washers (#5), and hex nuts (#6). Draw nuts up snug, 
do not tighten at this time.

2. Attach right-hand hitch plate (#2) to the inside of 

clevis plate “B” with 3/4”-10 x 2” GR5 bolts (#4), lock 
washers (#5), and hex nuts (#6). Draw nuts up snug, 
do not tighten at this time.

3. Attach back straps (#3) to the inside of mounting 

lugs “C” with 3/4”-10 x 2” GR5 bolts (#4), lock 
washers (#5), and hex nuts (#6). Draw nuts up snug, 
do not tighten at this time. 

4. Align holes in back straps (#3) with lower holes in 

hitch plates (#1 & #2). With 2" long spacer (#7) 
positioned in the center, insert 3/4"-10 x 5 1/2" GR5 
bolt (#8) through hitch plate (#1), rear strap (#3), 
spacer (#7), rear strap (#3), and hitch plate (#2) as 
shown. 

5. Secure bolt with lock washer (#9) and hex nut (#10).

6. Tighten hex nuts (#6 & #10) to the correct torque.

NOTE:  

Shanks  are  not shown to make  hitch 

assembly instructions  easier to follow.

Tractor Requirements

Tractor horsepower should be within the range noted 
below. Tractors outside the horsepower range must not 
be used.Tractor horsepower should be within the range 
noted below. Tractors outside the horsepower range must 
not be used.

Horsepower Rating. . . . . . . . . . . . . . . . . . .45-120 HP
Hitch Type. . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-Point
Hitch Category . . . . . . . . . . . . . . . . . . . . . . Cat. 1 or II

WARNING

!

To avoid serious injury or death:  

A tractor hitched to the BB35 Series scraper must meet 

listed minimum horsepower requirements. Refer to 

“Horsepower Rating” below for listed requirements. Using 

an under horsepower tractor can result in loss of tractor 

control and cause serious injury or death.

Lightweight tractors with rear attached implements may 

need weights added to the front to maintain steering control. 

Consult your tractor Operator’s Manual to determine 

proper weight requirements and maximum weight 

limitations.

Torque Requirements

Refer to 

“Torque Values Chart”

 on page 16 t

determine correct torque values when tightening 
hardware. 

Summary of Contents for BB3578























Reviews: