![background image](http://html.mh-extra.com/html/land-pride/accu-z-razor-z48/accu-z-razor-z48_operators-manual_672952048.webp)
46
Section 5: Maintenance & Lubrication
Z48, Z54, ZSR54 & ZSR60 Accu-Z Razor
®
Zero Turn Mowers 357-344M
11/05/10
Table of Contents
Mower Blade Maintenance
Blade Inspection
Check mower blades daily, they are the key to power
efficiency and well groomed turf. Keep them sharp, a dull
blade will tear rather than cut grass, leaving a brown
ragged top on the grass within a few hours. A dull blade
also requires more power from the engine.
Replace any blade which is bent, cracked or broken.
!
WARNING
DO NOT try to straighten a blade that is bent. Never weld a
broken or cracked blade. ALWAYS replace with a new Land
Pride blade to assure safety.
!
DANGER
Never work with blades while engine is running or blade is
engaged. Always place blade engagement switch in the down
(OFF), place both control levers in neutral and fully (OUT),
set park brake (ON) and turn engine (OFF). Block up mower
when you must work under it. Wear gloves when handling
blades. Always check for blade damage if mower strikes rock,
branch or other foreign object during mowing!
Cutting Blade Removal & Installation
1.
Remove blades by grasping blade end with a rag or
thick padded glove while loosening blade bolt.
2.
With a 11/16” wrench, remove 1/2” center blade bolt
and Washer from bottom of cutting blade.
3.
Reinstall blade, blade washer and bolt. Care should
be taken when installing the blade bolt to not get it
cross threaded.
4.
Tighten blade bolt to the correct torque. See
“Additional Torque Values” on page 58 for correct
torque values.
Blade Sharpening
!
CAUTION
ALWAYS wear eye protection and gloves when sharpening a
blade.
IMPORTANT: Blade mounting bolts have right hand
threads. Turn blade bolts counterclockwise to loosen
and clockwise to tighten.
IMPORTANT: Replace blades with Land Pride
blades only.
IMPORTANT: Always install blades with cutting
edge facing direction of blade spindle rotation and
with wing tips pointing up towards bottom of deck.
NOTE: Care should be taken in order not to remove
any more material than necessary to sharpen blade.
1.
If the blade cutting edge is dull or nicked, it should be
replaced or sharpened.
2.
Clean blade, blade washer and mounting surface of
all debris before replacing or sharpening.
3.
Sharpen blades on a grinder following pattern as
shown in Figure 5-22. Grind cutting edge at the same
bevel (27 1/2 degrees) as the original. Sharpen only
the top of the cutting edge to maintain sharpness.
Touch-up sharpening can be done with a file.
Blade Resharpening
Figure 5-22
!
DANGER
Keep blades balanced when sharpening. An unbalanced blade
may come loose and fly out from under the deck. Also, an
unbalanced blade will shorten the spindle bearing’s life.
4.
Balance of a blade is generally maintained by
removing an equal amount of material from each end
of the blade when sharpening. Check blade balance
by positioning the blade horizontally on a nail or shaft
through the center hole. See Figure 5-23. If either
end of the blade rotates downward, grind (remove)
metal on that end until the blade will balance. The
blade is properly balanced when neither end drops. If
blade is out of balance, true it up before reinstalling.
Blade Balancing
Figure 5-23
Resharpening Pattern
Do not sharpen to original pattern (below).
It is easier to get a straight cutting edge following
the resharpening pattern shown above.
Original Edge
19074
19075
NAIL OR SHAFT
HORIZONTAL
19046