Land Pride 7000 Series Operator'S Manual Download Page 3 | Manualshive

Page: 3 / 38

background image

Table of Contents

Table of Contents

9/16/20

7000 Series 556-433M

©

Copyright 2020 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this

product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Section 1: Important Safety Information. . . . . . . . . . 1

Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Section 2: Introduction . . . . . . . . . . . . . . . . . . . . . . . . 8

Description of Unit . . . . . . . . . . . . . . . . . . . . . . . . . 8

Intended Usage . . . . . . . . . . . . . . . . . . . . . . . . 8

Models Covered . . . . . . . . . . . . . . . . . . . . . . . . 8

Document Family . . . . . . . . . . . . . . . . . . . . . . . 8

Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 8

Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Owner Assistance. . . . . . . . . . . . . . . . . . . . . . . . . . 9

Further Assistance . . . . . . . . . . . . . . . . . . . . . . 9

Section 3: Preparation and Setup . . . . . . . . . . . . . . 10

Prior to Going to the Field Checklist . . . . . . . . . . . 10

Hitching Disk Harrow to Tractor . . . . . . . . . . . . . . 11

Electrical Hookup . . . . . . . . . . . . . . . . . . . . . . 12

Hydraulic Hose Hookup . . . . . . . . . . . . . . . . . 12

Clevis Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Category III Hitch . . . . . . . . . . . . . . . . . . . . . . . . . 13

Category III & IV Hitch . . . . . . . . . . . . . . . . . . . . . 14

Transport Locks . . . . . . . . . . . . . . . . . . . . . . . 14

First time Field Adjustments . . . . . . . . . . . . . . . . . 15

Pre-Leveling of Machine. . . . . . . . . . . . . . . . . 15

Scraper Adjustment . . . . . . . . . . . . . . . . . . . . 15

Section 4: Operating Instructions . . . . . . . . . . . . . . 16

Start Checklist . . . . . . . . . . . . . . . . . . . . . . . . 16

Section 5: Transporting the No-Till Drill . . . . . . . . . 17

Transport Checklist . . . . . . . . . . . . . . . . . . . . 17

Field Operations . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Field Set-Up Checklists . . . . . . . . . . . . . . . . . 18

Operations Checklists. . . . . . . . . . . . . . . . . . . . . . 19

Hitching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Field Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Field Turns . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

End Field Work. . . . . . . . . . . . . . . . . . . . . . . . 19

General Operation and In-Field Adjustments . . . . 19

Transport Locks . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Thread Protectors . . . . . . . . . . . . . . . . . . . . . . . . . 21

Adjusting and Using Tractor Hydraulics

Depth Control . . . . . . . . . . . . . . . . . . . . . . . . . 21

Tractor Detents. . . . . . . . . . . . . . . . . . . . . . . . 21

Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Rear Attachment Settings. . . . . . . . . . . . . . . . . . . 23

Spike Drag Settings (Option) . . . . . . . . . . . . . 23

Heavy Coil Tine Settings (Option) . . . . . . . . . 23

Rolling Harrow and Reel (Option) . . . . . . . . . 24

Section 6: Maintenance and Lubrication . . . . . . . . 25

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

End of Season . . . . . . . . . . . . . . . . . . . . . . . . 27

Beginning of Season . . . . . . . . . . . . . . . . . . . 27

Section 7: Appendix A

Reference Information . . 28

Specifications and Capacities. . . . . . . . . . . . . . . . 28

Tire Inflation & Warranty. . . . . . . . . . . . . . . . . . . . 29

Hydraulic Connectors and Torque . . . . . . . . . . . . 29

Torque Values Chart . . . . . . . . . . . . . . . . . . . . . . 30

«
1
2
3
4
5
...
»

Summary of Contents for 7000 Series







































Reviews:

No comments

Related manuals for 7000 Series

Brand: CAMPAGNOLA Pages: 4

Brand: ECE Pages: 2

Brand: Ecco Pages: 5

Evolution Series

Brand: Bakare Pages: 38

Brand: Pari Pages: 282

Brand: Pari Pages: 11

Brand: Pari Pages: 2

Brand: Haas Pages: 5

Brand: Vahterus Pages: 31

Brand: Baileigh Industrial Pages: 12

RZN 43-E Series

Brand: D+H Pages: 2

Brand: Tarmo Pages: 4

Brand: zapco Pages: 14

Brand: Rigol Pages: 12

Avisa Line XL04

Brand: FHF Pages: 2

Brand: Joerns Healthcare Pages: 106

evolution G-50 H

Brand: GAMA Pages: 48

Brand: Festo Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands