Land Pride 7000 Series Operator'S Manual Download Page 33

Page: 33 / 38

Appendix A

Reference Information

Table of Contents

9/16/20

7000 Series 556-433M

Tire Inflation & Warranty

Hydraulic Connectors and Torque

Refer to Figure 18 (a hypothetical fitting)

Leave any protective caps in place until immediately

prior to making a connection.

Tire Inflation Chart

Tire Warranty Information

Wheel

Tire Size

Inflation

All tires are warranted by the original manufacturer of the tire.

Tire warranty information is found in the brochures included

with your Operator’s and Parts Manuals or online at the manu

facturer’s web sites listed below. For assistance or informa

tion, contact your nearest Authorized Farm Tire Retailer.

Manufacturer Web site

Firestone

Gleason

Titan

Galaxy

BKT

Transport

11L X 15 Load

73 psi

(503 kPa)

)

NPT

- National Pipe Thread

Note tapered threads, no cone/flare, and no O

ring.

Apply liquid pipe sealant for hydraulic applications.

Do not use tape sealant, which can clog a filter

and/or plug an orifice.

)

JIC

- Joint Industry Conference (SAE J514)

Note straight threads and the 37



cone on

“M” fittings (or 37



flare on “F” fittings).

Use no sealants (tape or liquid) on JIC fittings.

)

ORB

- O

Ring Boss (SAE J514)

Note straight threads and elastomer O

Ring .

Prior to installation, to prevent abrasion during tight

ening, lubricate O

Ring with clean hydraulic fluid.

Use no sealants (tape or liquid) on ORB fittings.

ORB fittings that need orientation, such as the ell

depicted, also have a washer and jam nut

(“adjustable thread port stud”). Back jam nut away

from washer. Thread fitting into receptacle until

Ring contacts seat. Unscrew fitting to desired

orientation. Tighten jam nut to torque specification.

.eps

100%

Figure 18

Hydraulic Connector ID

31282

Table 1:

Table 2: Fittings Torque Values

Dash

Size

Fitting

N-m

Ft-Lbs

-4



- 18 NPT

1.5-3.0 turns past fin

ger tight

-5



- 20 JIC

19-20

14-15

-5



- 20 ORB w/jam

nut

12-16

9-12

-5



- 20 ORB straight

19-26

14-19

-6



-18 JIC

24-27

18-20

-6



-18 ORB w/jam

nut

16-22

12-16

-6



-18 ORB straight

24-33

18-24

Summary of Contents for 7000 Series







































Search results

Summary of Contents for 7000 Series

Reviews:

Related manuals for 7000 Series

Brands by name

Popular brands

Land Pride 7000 Series, Operator'S Manual

Search results

Summary of Contents for 7000 Series

Reviews:

Related manuals for 7000 Series

Brands by name

Popular brands