manualshive.com logo in svg

Land Pride 3P806NT, Operator'S Manual

Share
Download
Land Pride 3P806NT Operator'S Manual Download Page 31

Operating Instructions

Table of Contents

2019-01-23

3P806NT 313-520M

27

4. When raised for turns, obstructions and transport, 

the drive wheel stops, and the meter counts no 

additional (non-planting) rotations.

5. Whenever shaft rotation stops, the LCD display 

activates after 30 to 60 seconds, and remains visible 

for 30 to 45 minutes.

6. At the completion of planting, record the final reading 

or the grand total. If the display goes dormant before 

you can read it, see “

Dormant Display

”.

7. Subtract the reading at step 1 from the reading at 

step 6 for the total planted in the present session.

Dormant Display

Refer to Figure 14

To conserve power, the LCD display blanks itself most of 

the time. If you need to read the display after it has 

“timed out” and gone dormant:
• use the calibration crank to turn the jackshaft once, or
• gently tap or wave a magnet at either of the logo 

spots  on the lower region of the display. Be careful 

not to scratch the window.

When active, the lower left corner displays the 

revolutions per acre for which the meter is 

factory-programmed.

Field Operation

1. Hitch drill to a suitable tractor (page 14).

Crushing Hazard:

You may be severely injured or killed by being crushed 
between the tractor and drill. Do not stand or place any part of 

your body between drill and moving tractor. Stop tractor 

engine and set park brake before installing pins.

2. Remove caster pivot swivel locks if installed 

(page 21).

3. Fully raise drill (page 19).
4. Rotate gauge wheel. Check that feed cups, seed 

tubes and drives are working properly and free from 
foreign material.

5. Remove lift-assist cylinder transport locks and store 

on weldments (page 20).

6. Install Stroke Control Spacers (page 17).
7. Load materials (page 24).
8. Set initial seed population from Seed Rate manual.
9. Rotate gauge wheel to fill cups. Check for flow at 

opener tubes.

10. Calibrate material rates (see Seed Rate Manual).
11. Record initial acremeter reading (page 26).
12. Pull forward, lower drill, set both hitch and lift-assist 

circuit to Float, and begin seeding.

13. When turning at row ends and for other short-radius 

turns, always raise drill (tractor 3-point lift arms and 
lift-assist). Seeding automatically stops when the 
ground drive wheel loses contact.

Parking

Perform the following steps when parking the drill for 36 

hours or less. Refer to “

Storage

” to prepare for lon-

ger-term storage.
1. Position drill on a level, solid area.
2. Lower tractor 3-point lift arms and Retract lift-assist 

cylinder (page 20) until drill is on the ground.

3. Set lift-assist circuit to Float, to relieve all pressure.
4. Remove pins from lower 3-point links on drill (not 

from the front of any hitch extension in use).

5. Disconnect lighting harness and any other electrical connections.

1

Figure 14

Meter Display

28409

1

Semi-mounted implements with rear lift-assist wheels 
maneuver differently in field and highway transport, compared 

to pull-type implements. Observe caution when turning and 

transporting.

Summary of Contents for 3P806NT





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands