manualshive.com logo in svg

Land Pride 3P806NT, Operator'S Manual

Share
Download
Land Pride 3P806NT Operator'S Manual Download Page 43

Troubleshooting

Table of Contents

2019-01-23

3P806NT 313-520M

39

Excessive seed cracking

Excessive field speed.

Reduce field speed.

Feed cup flutes not open enough.

Open feed cups to a wider position.

Feed cup door handle not open 
enough.

Open feed cup door handle to a lower posi-
tion.

Press wheels not 
compacting soil as 
desired

Too wet or cloddy.

Wait until drier weather or rework ground.

Press wheel depth does not match 
coulter depth.

Readjust press wheel depth, page 37.

Not enough down pressure on disc 
openers.

Increase down pressure on openers, 
page 35.

Boxes not emptying 
evenly

Some boxes do not have same num-
ber of feed cups between each 
divider of bulkhead.

Load more material than required. Re-dis-
tribute when re-loading.

Main box seed cup door setting

Set all doors the same, per seed size.

Seed plug(s) installed

Remove seed plug(s).

Meter or tube blocked.

Clear blockage.

Press wheel or openers 
plugging

Planting conditions too wet.

Wait until drier weather.

Too much down pressure on open-
ers.

Reduce down pressure on openers, 
page 35.

Backed up with drill in the ground.

Clean out and check for damage.

Failed disc bearings.

Replace disc bearings.

Scraper worn or damaged.

Replace scraper.

Feed cup sprockets 
locked up or twisted feed 
cup drive shaft

Foreign matter lodged in one or 
more feed cup sprockets.

Clean out feed cup sprockets. Use clean 
seed.

Dried liquid insecticide inside feed 
cups.

Remove build up by disassembling each 
feed cup and scraping foreign substance 
from turn surfaces.

Coulters not going deep 
enough

Not enough down pressure.

Adjust coulters when a few rows are 
involved (page 30). Add weight when all 
rows are affected (page 32).

Row down pressure set too high 
(reducing weight available to 
coulters)

Reduce row down pressure to standard 
(page 35). Set coulters to prepare furrow 
more aggressively (page 30).

Coulters and drill going 
too deep

Coulters set too deep or spring force 
too high

See page 30 for correct adjustment.

Incorrect press wheel adjustment.

Set press wheels to a shallower depth.

Coulters and openers 
plugging in no-till 
conditions

Drill at a slight angle to rows.

Problem

Cause

Solution

Summary of Contents for 3P806NT





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands