manualshive.com logo in svg

Land Pride 3P806NT, Operator'S Manual

Share
Download
Land Pride 3P806NT Operator'S Manual Download Page 18

Preparation and Setup

Table of Contents

3P806NT 313-520M

2019-01-23

14

Hitching Tractor to Drill

The 3P806NT is a 3-Point Category II hitch implement, 

employed in 2-point Semi-Mounted mode.
Note: The top link of the tractor 3-point is not used for 

transport or field operation. Full 3-point mode is 

incompatible with lift-assist.

1. Remove tractor drawbar before hitching. The drill 

gauge wheel tire or assembly will be damaged if it 

contacts the drawbar during hitching, raising or 

lowering operations.

2. If a hitch extension is required, install the extension 

or setback on the drill, per the instructions at “

Hitch 

Extension Installation

” on page 82, before 

continuing with hitching.

Equipment Damage Risk:

Great Plains CPH, PFH or SSH accessory hitches are not 
compatible with the 3P806NT.

Crushing Hazard:

You may be severely injured or killed by being crushed 

between the tractor and drill. Do not stand or place any part of 

your body between drill and moving tractor. Stop tractor 
engine and set park brake before installing hitch pins.

3. Raise or lower tractor 3-point lift arms, or hitch 

extension, as needed and pin lower arms to drill. 

Upper arm is unused.

4. Set your tractor 3-point draft control to Float position.

Equipment Damage Risk:

Do not raise tractor 3-point lift arms until after hydraulic and 
electrical connection have been made.

Summary of Contents for 3P806NT





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands