background image

21

Scheduled Maintenance/Cleaning

As Needed

•  Keep exterior surfaces of unit clean using a clean, damp cloth.

Daily

•  Using the cleaning solution, clean top cover and all exterior stainless steel surfaces.
•  Clean exterior of dispensing valves and ice chute.
•  Remove cup rest then clean the drip tray and cup rest. Replace cup rest when finished.
•  Wipe clean all splash areas using a damp cloth soaked in cleaning solution.
•  Clean beverage nozzles as specified by the section “Cleaning and Sanitizing Nozzles”.

Monthly

•  Clean the ice bin, auger, and ice chute assembly as specified by the section “Cleaning and Sanitizing 

Ice Bin, Auger, and Ice Chute” on page 22.

Every Six Months

•  Clean the syrup lines as specified by the section “Cleaning and Sanitizing Syrup Lines - Bag in Box” on 

page 23.

•  Pull out unit (if applicable) and clean behind and underneath. Check for any loose components or 

noises.

Cleaning and Sanitizing Nozzles

1.  Prepare the nozzle sanitizing solution as described on page 

20. 

2.  Turn the left and right key switches to deactivate valves and 

avoid accidental dispense while the nozzles are exposed.

3.  Remove the outer nozzle by twisting clockwise and pulling 

downward.  

 

DO NOT

 attempt to activate any valves while the outer 

nozzle is removed.

ATTENTION

4.  Using the nozzle brush provided in the installation kit and the 

cleaning solution described on page 20, clean the outer 

nozzle of any residual syrup.

5.  Rinse the outer nozzle with clean, potable water then soak in 

the nozzle sanitizing solution prepared in step 1.

6.  While the outer nozzle is in the sanitizing solution, using the 

nozzle brush, dip the brush in the nozzle sanitizing solution 

and thoroughly brush the bottom of the inner nozzle body.

7.  Rinse the brush in warm 90° – 110°F (32.2°– 43.3°C), clean 

potable water and brush the bottom of the inner nozzle body 

once more 

WITHOUT

 the sanitizing solution.

8.  After the outer nozzle has soaked for fifteen (15) minutes, 

rinse in warm 90° – 110°F (32.2°– 43.3°C), clean potable 

water for a minimum of twenty (20) seconds ensuring all 

surfaces of the nozzle have been thoroughly rinsed.

9.  Allow outer nozzle to air dry (to expedite drying, forced  

convection is recommended).

10.  Reinstall the outer nozzle to the unit.
11.  Repeat Steps 3 - 10 for the second nozzle.
12.  Return the left and right key switches to active valves.

A

A. Nozzle

Summary of Contents for Twin Pour



































Reviews: