![background image](http://html1.mh-extra.com/html/lancer/portion-control/portion-control_operation-manual_672721021.webp)
FIGURE 24 - SYRUP SOLENOID ASSEMBLY
O-Ring
Plug Nut
O-Ring
Solenoid
Coil
O-Ring
Core/Spring
Solenoid
NOTE: Part Number in ( ) is a Coca-Cola PN
02-0005
(10050)
10-0280/04
(24230)
02-0538
(10061)
Bonnet
81-0407/01
(24224)
Washer
04-0820/01
(24226)
12-0132/04-01
(24225)
Assembly
82-1624/03
(24229)
02-0109
(17428)
19.2 SYRUP SOLENOID INSTALLATION - CONTINUED
F. Insert syrup down tube into port on the side of the syrup body sub-assembly.
G. Apply 111 Lubricant to the outside edge of o-ring on the syrup solenoids.
H. Carefully press the syrup body sub-assembly into place on top of the syrup solenoids. If the
syrup body will not smoothly press into place, then apply more 111 Lubricant to the solenoid
o-rings, so that they will not be pinched. Make certain the syrup down tube goes into the down
tube port on the valve body. If the solenoid assembly becomes unseated, remove solenoid
assembly and repeat Steps A through D above. Hold the syrup body firmly in place until the
mounting screws are completely installed.
I. Install two (2) upper screws located at front and rear of syrup body.
J. Install two (2) screws on the underside of main body, to secure the syrup body.
K. Place the flowmeter wires around the outside of the flow washer assembly, so that they will not
interfere with the bottom plate installation.
!
CAUTION
DO NOT PINCH ANY WIRES DURING INSTALL
PRECAUCIÓN
NO NO PELLIZQUE NINGÚN CABLE DURANTE LA INSTALACIÓN.
ATTENTION
VEILLER À NE COINCER AUCUN FIL LORS DU MONTAGE.
!
CAUTION
THE PLUG NUT MAY PULL OUT OF THE COIL, WHEN
TRYING TO LOOSEN. THE COIL CAN BE DAMAGED IF DROPPED.
PRECAUCIÓN
LA TUERCA DE LA CLAVIJA PUEDE ZAFARSE DE
LA BOBINA, CUANDO SE TRATA DE AFLOJARLA. SI SE CAE LA
BOBINA SE PUEDE DAÑAR,
ATTENTION
IL SERA POSSIBLE QUE L’ÉCROU DE BLOCAGE
DE LA BOBINE SE DÉSOLIDARISE DE CETTE DERNIÈRE LORS
DU DESSERRAGE DE L’ENSEMBLE. VEILLER À NE PAS FAIRE
TOMBER LA BOBINE, AU RISQUE DE L’ENDOMMAGER.
L. Line up holes on the bottom plate with the screw
holes on the underside of the main body.
M. Secure bottom plate in place with four (4) screws.
N. Install nozzle/diffuser
O. Install lever arm, if applicable.
P. Install circuit board (see Circuit Board, Section 12).
20. SYRUP SOLENOID ASSEMBLY
20.1 DISASSEMBLY
A. Remove the core/spring assembly from the solenoid.
B. Slide the o-ring off the end of the solenoid.
C. Lift the solenoid washer off the end of the solenoid.
D. If the o-ring remains in the end of the syrup plug nut or
on the post inside the syrup solenoid mounting area on
the main body, remove it.
E. Carefully hold the wire terminal block on the side of the
coil while pulling the solenoid bonnet to loosen the
syrup plug nut. When the syrup plug nut has been
pulled out of the coil enough, remove it and the bonnet
by hand.
20.2 ASSEMBLY
A. Slide o-ring into the groove on the syrup plug nut.
B. Slide bonnet over coil.
C. Apply 111 Lubricant to o-ring in plug nut, then press plug nut into top of coil/bonnet assembly.
D. Place solenoid washer on bottom end of coil/bonnet assembly.
E. Place o-ring over end of coil extending through solenoid washer.
F. Insert the core/spring assembly into the end of the solenoid assembly.
NOTE:
Water and syrup solenoid coils are interchangeable.
21