background image

 

CAUTION!!! - ONLY USE OUTDOORS

 

 

This product was designed and tested for outdoor use alone. Indoor installations are not allowed; 

 

Safely position the hot spot so that it cannot be accidentally hit 

 

Position the hot spot as horizontally as possible 

 Do not use the unit as an incinerator or in any other way other than that for which it was designed; 

 No other fuel besides wood pellets must be used; 

 Do not use liquid fuels; 

 When the stove is turned on, it can reach extremely high temperatures to the touch, especially its outer 

surfaces. Operate carefully to avoid burns; 

 Do not make any unauthorised modifications to the device; 

 Only use original replacement parts recommended by the manufacturer; 

 Make sure that all exhaust system joints are hermetically sealed with silicone, are resistant to heat (250 

°C) and are not damaged. 

CAUTION

: keep all flammable products well away from the product when it is operating (MINIMUM: 100 

cm from the front wall). 

CAUTION

: to prevent the escape of fumes, the combustion chamber must be kept closed except during 

cleaning operations, to be carried out when the product is off. 

CAUTION

: in the event of pellet supply when the product is on, make sure that pellets are not finished and 

that the flame is always present and live in the brazier. 
Do not refill the tank if you notice that the pellet is ending and the flame is absent or low. 

Failure to comply with this indication can be dangerous and cause fume malfunction and their 

explosion 
CAUTION

 prevent the fuel bag to come into contact with hot surfaces. 

CAUTION

: remove any residue of unburned pellets caused by failed ignitions before starting the hot spot 

again 

CAUTION

: if during the ignition phase, the product does not start and you notice a lot of smoke in the 

combustion chamber, immediately turn off the stove and replace the pellets being used, as these may be too 
high in moisture. Forcing ignition could make your product a hazard. 

CAUTION

: if during cleaning, you find traces of spongy or hard (though not ash) pellets, replace the pellets 

being used, as this residue may come from scraps of low quality sawdust not usable in this type of product. 
Forcing ignition can cause a fire or lots of smoke. 

CAUTION

: monitor proper combustion of the pellets in the brazier. Should you detect accumulations of 

unburned pellets, IMMEDIATELY TURN OFF the product and contact the service centre. 

CAUTION

: pay the utmost attention in the presence of children. 

Summary of Contents for IDRO Hot Spot 13 Wind

















Reviews: