Lambrecht meteo 15189 Operating Instructions Manual Download Page 6

(15189 analog) Precipitation Sensor  

         Operating Instructions 

Operating Instructions
Precipitation Sensor (15189 analog)

Further setting options

Changes of the basic settings are urgently allowed 
in power-off mode. Only if necessary, changes of 
the basic setting should be carried out by skilled 
technician.
Changes of settings will be accepted only after recon-
necting the power supply. Changes of the jumpers 
during operation are not allowed.
Please note, changes of the basic settings by users 
will be carried out on own responsibility. The manu-
facturer is not liable for consequential damages.

Overview of the selectable operating modes

•  4 analog outputs selectable:

0...20 mA · 4...20 mA •  0...5 V · 0...10 V

• 4 

fi

 nal values of the measuring ranges* for the analog 

outputs selectable: 10 / 20 / 25 / 50 [mm]

•  4 time-frames of the analog outputs for gliding summa-

tion selectable: 1 / 10 / 30 / 60 [minutes]

•  2 modi for low power operation regarding pulse output 

and power supply selectable

Functions of the jumpers

See also tab. 1:

• 

J3 

to select the required mode (Pos. 1-8)

• 

J4, J5 

to switch on the respective analog output

• 

J6 

to switch over the analog voltage output

• 

J12 

to connect the switch output to the power supply for 

2 wire circuit of the low power modi (not plugged  = power 
supply and pulse output are separated)

   • 

J10

 must be plugged always at the middle position,

 

  see 

fi

 g. 14!

Fig. 8: Positions of the jumpers, which are usable for changes 
of modi

* These data refer to 2 cm

3

 volume of tipping bucket.

Tab. 1:   Setting options
 

"x" ... jumper plugged; "-" jumper unplugged

Services:

97.15180.000 000 

User-specifi c confi guration 
of the precipitation sensor 

Note: This service is required, if the basic settings of the 
should be modi

fi

 ed by factory.

In principle the changes of the con

fi

 guration can be carried 

out on-site by user themselves.

J3

J4 J5 J6 J12

             Position
Mode

1 2 3 4 5 6 7 8

0...20 mA

-

-

x

x

-

4...20 mA

-

x x

x

-

0...5 V

x -

x

x

x

0...10 V

x x x

x

-

10 mm

-

-

x

x

20 mm

-

x

x

x

25 mm

x -

x

x

50 mm

x x

x

x

1 minute

-

-

x

x

10 minutes

-

x

x

x

30 minutes

x -

x

x

60 minutes

x x

x

x

Low Power, only
pulse output
separate
pulse output

-

-

-

-

-

-

-

-

-

-

-

Low Power, only
pulse output
2 wire circuit

-

-

-

-

-

-

-

-

-

-

-

x

Analog output, 
absolute sum

-

x

x

x

Analog output, 
gliding sum

x -

x

x

6

J12

J3

J4

J5

J6

J10

Summary of Contents for meteo 15189











Reviews: