Lamborghini Caloreclima DORA TECH 90 LT, User, Installation, And Maintenance Manual

Page: 74 / 112

DORA TECH
90 LT - 120 LT
cod. 3540000800 - Rev. 02 - 09/2023
74
EN
NOTA:
* : for the correct reading of this parameter, the va-
lue resulting from the 3 screens must be divided by 10.
Ex. 02859 / 10 = 285,9
** : for the correct reading of this parameter, the value re-
sulting from the 3 screens must be multiplied by 10.
Ex: 02859 x 10 = 28590
2.8.6 rSt menu - RESET
Para-
meter
Description
Note Level min max Livello
n01 Weekly programming reset - 0 0 1
U / I
n02 Energy monitoring counter reset - 0 0 1
U / I
Level: U=user menu - I=installer menu
To perform the reset:
• set the parameter = 1
• power off the unit
• power on the unit.
2.8.7 Inf MENU - MACHINE STATUS INFORMATION
To view the general information, access the Inf menu by pres-
sing the “SET” key and scrolling with the “+” and “-” keys,
the values “I01” to “I13” will appear.
Para-
meter
Description
Note Level
I01 Currently active operating
mode
0:6 (0=OFF, 1=STANDBY, 2=ECO, 3=AUTO,
4=BOOSTER, 5=ELECTRIC, 6=FAN)
U / I
I02 real water set point* °C
U / I
I03 External air temperature °C
U / I
I04 Lower water temperature °C
U / I
I05 Higher water temperature °C
U / I
I06 Evaporator inlet temperature °C
U / I
I07 Evaporator outlet tempe-
rature
°C
U / I
I08 Compressor delivery tem-
perature
°C
U / I
I09 Coil temperature °C
U / I
I10 PT1000 solar probe tempera-
ture (unusable)
°C
U / I
I11 - Reserved
U / I
I12 Calculated evaporation
temperature
°C
U / I
I13 Calculated condensing
temperature
°C
U / I
I14 Electronic expansion valve
opening
Step
U / I
I15 Fan rpm number rpm / 10
U / I
I16 WiFi module firmware
- U / I
I17 Motherboard firmware -
U / I
I18 Display firmware
- U / I
I19 Parameter version
- U / I
Level: U=user menu - I=installer menu
* : the displayed value also takes into account any offsets linked to the
activation of the auxiliary functions (photovoltaic, smartgrid, solar thermal,
anti-legionella).
Press the “ON/OFF” key to exit the menu.
2.8.8 HI menu - ELECTRIC HEATER SETTING
Value Description
Unit of
measure default min
max Level
H01
Enabling heater in ECO mode when
protection alarm
(0=disabled, 1=enabled)
-
0 0 1
I
H02
Electric heater ignition upper probe
hysteresis (only for Electric and Booster
modes)
°C 7 0 20
I
H03
Operating time in AUTO mode for
temperature rise control for switching
on the electric heater
min 30 0 120
I
H04
Minimum increase in water temperature
so as not to turn on the heating element
in AUTO mode
°C 4 0 30
I
Level: U=user menu - I=installer menu
Parameters:
H01 : from this parameter it is possible to enable or disable the
switching on of the heater when the unit is working in ECO
mode and the compressor cannot switch on due to an inter-
vention of one of its protections (for example intervention of the
HP pressure switch or air temperature at outside the operating
limits):
H02: Difference between the set point and the heater switch-
on temperature
H03 – H04
: These parameters are used when the unit is wor-
king in AUTO mode and you want the heater to be turned on
when the water temperature does not rise by a minimum in-
crease (H04) after a given pump operating time of heat (H03).
NOTE
: once turned on, the heater will turn off only when the
water temperature reaches the set point
2.8.9 Phv menu - EVU functionality - Photovoltaic functio-
nality
If parameter G01=1 is set (smartgrid enabled), the
EVU and photovoltaic functions are not available. To
enable them, set parameter G01=0 (smartgrid not ena-
bled).
2.8.9.1 EVU functionality (see also “6.8.1 Remote connec-
tions”)
This function is indispensable if a subsidized electricity tariff is
subscribed for heat pumps. The aim is to facilitate operation
when the cost of electricity is low, but still having to comply with
the rules of the energy supplier who will be able to decide when
to interrupt the supply.
To meet this requirement, the water heater electronics are fit-
ted with a digital input which, when opened, allows the unit to
be switched off and thus reduce the load on the electricity grid.
NOTE: When enabled and active, this feature takes priority
over the PV feature.
To set the parameters, access the phv menu, by pressing the