laguna CEF236230175, Setup And Maintenance Manual

Page: 16 / 45

Fusion Tablesaw
16
Setup
Use Caution:
Your new Laguna Tools machine is heavy. Use a
minimum of two people when lifting the tool into position and moving
the tool into position.
Tech Tip:
A setup video is available at
lagunatools.com/classic-machinery/tablesaws/f2-fusion/
or www.youtube.com/watch?v=FOPstZ61uFs
warning:
To avoid set-up problems, to prevent potential damage
to the machine and personal injury, read through the entire setup
section prior to setting up the machine.
warning:
DO NOT connect to a power supply until the setup is
complete. DO NOT perform any of the following steps, installations,
or adjustments with the saw connected to the power source.
Receiving and Unpacking
If any damage has occurred because of shipment, note the damage on the bill of lading or refuse the shipment. Immediately call the dealer store
where the machine was purchased
TRANSPORTATION AND STORE The measures of anti-rust and shockproof should be taken during packing. The machine endures transportation
and store in -25~55°C ambient temperature.
Be care of not making machine exposed to rain or damaging the packing during transportation and store.
While transporting or handling the machine, be careful and let the activity be done by qualified personnel especially trained for this kind of activity!
While the machine is being loaded or unloaded, make sure that no person or subject gets pressed by the machine!
Select proper transportation device according to the weight of the machine.
Make sure the lifting capacity of transportation device is competent for the weight of the machine.
TRANSPORTATION BEFORE UNPACKING As standard, the machine is packed in a robust wooden
box.
Fig.1 shows the tool can be used to transport the packing box.
UNPACKING
1. Receiving your tablesaw.
2. Unscrew the crate fasteners.
3. Lift crate off pallet.
4. Check Inventory.
5. Wipe off protective oils. Unscrew the crate fasteners
This is how the machine is shipped from the
factory. Use a drill or screw driver with a #2 Phillips head
bit and remove the bottom screws from carton.
These screws may be discarded.
Lift crate off pallet Check Inventory Wipe off protective plastics
Use two persons to lift the carton away from the
pallet. There should be three packages along with
the table saw.
NOTE: The throat plate, riving knife, and 10” blade is pre-installed in
the machine. The miter gauge, and blade changing tool are positioned
in the tool holder located on the right side of the cabinet.
1. Fence, install tools, push stick, blade
guard assembly
2. Smaller fence rail sections, hardware kit
3. Longer fence rail sections.
Peel back the protective vinyl plastic and wipe
away the oil with a waste rag.
Use Caution:
An oily rag can
be a serious fire hazard. Discard
in an appropriate manner.
Tech Tip:
To help keep your table top clean and to prevent or clean any rust, we recommend waxing your tabletop with an appropriate wax
rubbing compound. This will also reduce friction under operation. Rust can be removed with WD-40.
Inventory
Box 1 contents Box 2 contents Box 3 contents Pre-Installed on machine
Fence PTSF236110175-0130-1-1 Rear Rail 2 PTSF236110175-0130-127.5 Rear Rail 1 PTSF236110175-0130-127.5 Throat Plate PTSF236110175-0130-6
Push Stick PTSF236110175-0130-130 Front Rail 2 PTSF236110175-0130-127.6 Front Rail 1 PTSF236110175-0130-127.6 Riving Knife PTSF236110175-0130-27
Blade Guard
PTSF236110175-0130-2-1
Hardware kit
-
10” Blade PTSF236110175-0130-33
Install Tools - Miter Gauge PTSF236110175-0130-3
Fence Hooks* PTSF236110175-0130-118 Arbor Wrench PTSF236110175-0130-137
*Fence storage hooks may be pre-installed. Tool Storage PTSF236110175-0130-120
Fig.1
Receiving your tablesaw
NOTICE:
For safety reasons, this machine is not sold with a tape-rule for the left side of the blade. It is not a missing part.
Wing (2) PTSF236110175-0130-4
Notice:
The front rail part number is comprised of two pieces – both long and short. The rear rail part
number is comprised of two pieces – long and short.