E
N
G
L
IS
H
Resusci Anne
7
Note: The maximum compression depth indicator is de-activated on
this product in accordance with 2010 Guidelines.
Wrong hand position
The yellow LEDs will be activated if chest is depressed outside
the correct area either on one of the sides or at the upper part
of thorax. The red LED will be activated if the chest is
depressed with hands placed outside the correct area at the
lower center part of thorax. This will in addition to visual feed-
back also be recorded on the printout report as “!” next to
the compression curve.
Responsiveness check
The manikin has a shake sensor installed that will be activated by
gently shaking the manikin. This will result in a “r” in the printout
report. This will only be possible if responsiveness check is done
before any other CPR is performed.
Open airway
The manikin has a neck sensor installed that will be activated by
head tilt/ chin lift to indicate open airway. This will result in an
“a” in the printout report and will only be possible before any
other CPR activity is performed.
Pulse check
The manikin has sensors installed that will be activated by caro-
tid pulse check for 10 seconds on either side of the throat. This
will result in a “c” in the printout report. If pulse is re-checked, it
will only show in the report if CPR activity is performed
between the two pulse checks.
Power Supply
The eight 1.5 V alkaline batteries, size D, are located inside the
manikin chest and will provide approximately 125 hours of use
(without printing) in the classroom. This will vary depending
on use patterns and brand of batteries. These batteries are the
“power supply” for both the manikin and the SkillReporter.
Battery low indication
“On” LED on SkillReporter will start to flash when only 25 % of
battery capacity is left. At this level the print-out function may
stop.
When “On” LEDs on both manikin and SkillReporter start
flashing, you should replace batteries to avoid that logging/feed-
back stops.
Connection Cable
This is permanently connected to the SkillReporter and has an 8
pin male connector that is to be connected to the manikin.
1
2
3
ON
Long report
E
The long report format can be printed either during logging or
after logging of the CPR data.
This report consists of an analog part showing ventilation and
compression curves along with a time-line, and also the different
actions taken during the session, followed by statistical data as
described above.
Print-out during logging
When pressing the “long print” key during CPR performance, an
analog printout in real time of the CPR curves will be printed if
the log function has been activated.
When the logging is stopped, a statistical report of the CPR(-D)
performance data as described above, will be printed.
Print-out after logging
It is also possible to print a long format report (both analog
curves and statistical data) after a scenario is finished if the log
function has been active.
Installing new paper
Be sure that the SkillReporter
is connected to the manikin
and turned “ON”. Open the
paper lid at the back of the
SkillReporter. Place the paper
roll as shown on illustration.
Insert the paper end into the paper
inlet and the paper will automatically
feed into the SkillReporter. Close the
paper lid. If paper jam occurs, move the
handle at the side of the SkillReporter to upright
position, pull paper from front until paper roll is rotating.
Move the handle back to its original (horizontal) position.
Diagnostic printout (Teststrip)
To activate the diagnostic printout: Press ‘’short print’’ key and
hold, then press ‘’long print’’ key and release both.
Manual paper feed
To activate manual paper feed: Press ‘’long print’’ key and hold,
then press ‘’short print’’ key and release both.
Inflation
The inflation volume is shown by a bar graph with different LED
colours indicating insufficient, sufficient and excessive volumes.
Between 0 and 0.5 l, the yellow LED(s) will be activated
indicating insufficient inflation volume. When lung inflation
volume reaches 0.5 l to 0.8 l, the green LED(s) will be activated
indicating sufficient inflation volume. If lung inflation volume
exceeds 0.8 l, the red LED(s) will be activated indicating
excessive inflation volume. A red warning light indicates a too
fast inflation (stomach insufflation).
Stomach insufflation will be indicated by “!” next to the
ventilation curve in the printout.
Chest compression
The compression depth is shown by a bar graph with different
LED colours indicating insufficient, sufficient and excessive com-
pressions. When the breastbone area of the chest is depressed
between 0 and 50mm (2”), the yellow LED(s) will be activated
to indicate insufficient compression depth. At 50mm (2”) and
deeper, the green LED(s) will be activated to show sufficient
compression depth.
