background image

 

Page 8 of 17 – US – 

Oven Orifice:  

To replace oven orifice: 
Remove  oven  baseplate. 

CAUTION: 

when  refitting  place  the 

base  underneath  the  groove  on  the  fascia  (Figures  16  and  17).  
Remove  screws 

L

  (Figure  18).    Remove  the  screen  below  the 

oven  (Figure  19).    Loosen  screw 

M

  then  slide  open  the  burner 

air collar towards the front of the oven (Figure 20).  Replace the 
orifice (Table 

5

). 

 

 Pilot burner orifice:  

Change the pilot burner orifice: 

Remove  slotted  cap  at  bottom  of  pilot  burner  assembly.  
Unscrew pilot injector.  Replace  new injector (Table 

5

), screw in completely until  injector bottoms out.  Replace cap 

screw. 

Gas pilot 

LP

: 65.103032 

Gas pilot 

NG

: 65.103031 

Table 5 

 

Ø 

GAS

 

Pressure

 

Oven 

Pilot burner 

Natural Gas 

6" WC 

1.40 

0.45 

L.P. propane 

10" WC 

0.95 

0.25 


 Adjustment of oven primary airflow: 

Remove the oven base plate, loosen the screw 

M

 that secures the air ring and then adjust (Table 6, Figure 20).

 

 

 





Table 6 

 

Opening in mm / 

inches 

GAS

 

Pressure

 

Oven 

Natural Gas 

6" WC 

4 / 

3

/

16

 

L.P. propane 

10" WC 

6 / 

1

/

4

 



Adjusting pilot burner air supply 

Turn ring 

N

 to fully open for Butane/Propane, to half open for natural gas (Figures 21) 

 
 
 
 
 
 
 
 
 
 

Fig. 20 

 

Air Adjustment  

 

 

 

Fig. 19 

Fig. 21 

Summary of Contents for RULLY


















Reviews: