background image

INSTALLER’S MANUAL

INSTALLER’S MANUAL

5

ADJUSTMENT OF THE HOB BURNER

ADJUSTMENT OF THE HOB BURNER

OPERATION

:

1   

Push down on the control knob and turn it anticlockwise; press simultaneously on the ignition 

pushbutton.

Once the burner is lit, release the ignition pushbutton. 

2

 Still pushing down on the control knob, set it to the small flame «

» 

setting.

  

After  about  ten  seconds  to  allow  for  the  engagement  of  the 

thermocouple, release the control knob.

3

 In the low flame setting, the flame must be low, steady and covering 

slightly the tip of the thermocouple.

►If  the  flame  goes  off  in  the  low  flame  setting,  repeat  the 

procedure. If after several attempts you are unable to hold the 

flame  in  the  low  flame  setting,  proceed  to  adjust  the  burner 

(refer to Section “Adjustment of the hob burners”).

►If in the low flame setting, the flame is too strong, then the gas 

delivery rate to the burner needs to be reduced.

Lacanche’s gas appliances are delivered fully adjusted in compliance with relevant regulations and

for use with the particular gas supply (type, pressure) stated in the purchase order and indicated in

the appliance’s nameplate.
Nevertheless, after connecting the appliance, the correct operation of the burners (hob and oven) 

must be checked. If required, the height of the flame must be adjusted accordingly.

To do this, the gas delivery rate to the burner must be adjusted by screwing in or out the valve 

adjustment screw located behind the control knob.
This adjustment is essential when changing the gas supply after having changed injectors (refer to 

Section “Change of gas”).

WARNING:

The adjustment of burners must be carried out by a qualified technician.

ADJUSTMENT OF THE FLOW RATE

:

The adjustment of the low flame gas delivery rate is carried out with the 

burner on and the control knob removed, using a small screwdriver to 

screw in or out the screw in the gas valve located behind the control.

4

  

Replace the control knob and turn it to the large flame « » setting.

5

  

Turn quickly from the large flame « » setting to the small flame «

» 

setting.
When doing this, the flame must remain burning.
At its minimum size, the flame must be a quarter (¼) in size of the full 

flame.

When this is not the case:
Repeat the procedure from 

1

 to 

5

.

1

 

With  the  burner  on,  set  the  control  knob  to  the  small  flame  «

» 

setting.

3

 

Screw  in  or  out  the  gas  valve  screw 

to  adjust  the  delivery  rate  for  the  low 

flame. Screwing out increases the flame. 

Screwing in reduces the flame.

2

   

Remove the control knob.

EN 

10-2016

Multicooker

Chargrill

Electric fryer

Gas burners

Induction

Ceramic Hob

Plancha

Summary of Contents for LAG 010 UR











Reviews: