background image

 

 

 

 

BA_072_2020-02_10.00  Pressure transmitter PASCAL Ci4 

Page 21/28 

 

6.4.5.1  Setting the damping 

Using an adjustable damping you can eliminate fast pressure changes or peaks from hav-

ing direct influence to the output signal. The set value in seconds corresponds to the time 

constant of an exponential rise. After a sudden pressure change, it takes the damping time 

to reach 63.2% of the actual pressure at the output. After the damping time has elapsed 

three times, 95% of the pressure is reached. 

  

 

Figure 14: Damping effect 

  

The damping affects the current output as well as the displayed pressure value. 

  

6.4.5.2  Setting of the measuring rate 

When shipped, the transmitter is set to a measuring rate of 20 Hz, i.e. 20 times per second 

the pressure is measured and the current is calculated and imprinted in the current loop. 

When a particularly fast measuring rate is required, for instance to detect pressure peaks, 

you can increase the measuring rate to 100 Hz. This can lead to the following restrictions: 

  

  Communication via HART can be disturbed by fast pressure changes. 

  The measuring signal can be noisier. 

  

For this reason, you should only increase the measuring rate to 100 Hz if necessary for the 

application. 
Note: Devices with differential pressure cell (type CI4x4x) run with a fixed measuring rate 

of 50 Hz. For these devices there is no option to set the measuring rate.  

  

Summary of Contents for CI4 Series





























Reviews: