background image

11 

 

 

Setting the Temperature Control 

 

The Wine Cooler has two temperature zones. 

  Upper zone – temperature range 5°C to 10°C 

  Lower zone – temperature range 10°C to 18°C 

 

You can set the required temperature either zone by pushing the 

Set Upper 

or 

Set Lower 

button. 

When you push the two buttons for the first time, the LED readout will show the previously set 
temperature set for that zones. 
The temperature preset at the factory are

: Upper zone: 

6°C, 

Lower zone: 

12°C 

To set the temperature in the Upper zone press 

Set Upper 

button once. The present temperature 

will flash. The temperature will decrease by every time the button is pressed until minimum 
temperature is reached, at which point it will then revert back to its maximum setting and start again. 
To set the temperature in the Lower zone press the 

Set Lower 

button and follow the instructions 

above. 
To view the temperature set in either zone at any time, press the corresponding “

Set Upper

” or “

Set 

Lower

” button, the “

Set

” temperature will temporarily flash in the LED display for 5 seconds. 

 

The controls of your Wine Cooler for CVDE21 – simple zone 

 

 

 

Indicator light illuminates to signify the cooling mode is currently in operation. 

 

 

To control this appliance, turn ON/OFF (press and hold this buttons for approximately 
2 seconds). 

 

 

To control the inner light, turn on/off. 

 

 

Used to set temperature. 

 

 

Setting the Temperature Control for CVDE21 – SIMPLE ZONE 

 

You can adjust temperatures from 5 to 18°. 
This is the same use instructions as CVDE46-2 

 

NOTE: 

  If the unit is unplugged, power lost, or turned off, you must wait 3 to 5 minutes before restarting 

the unit. If you attempt to restart before this time delay, the Wine Cooler will not start. 

  When you use the Wine Cooler for the first time or restart the Wine Cooler after having been  shut 

off for a long time, there could be a few degrees’ variance between the temperature you select 
and the one indicated on the LED readout. This is normal and it is due to the length of the 
activation time. Once the Wine Cooler is running for a few hours everything will be back to 
normal. 

Summary of Contents for CVDE46-2

















Reviews: