background image

43

English

11.2 Safety valve

The safety valve is installed on the upper part of the boiler, in the part corresponding to the area occupied 
by the steam. The valve is activated if there is a considerable pressure increase inside the boiler. The valve 
rapidly lowers the pressure by expelling the steam in the atmosphere (the valve trips in at 2÷2.5 bar). If the 
safety valve trips in, the steam is held and dissipated inside the machine frame, so as to avoid hazards for 
the persons around the machine. 

 

In case of activation of the safety valve, switch off the machine and immediately contact the spe-
cialized technician.If the safety valve is set off, switch the machine off and immediately contact 
the authorized La San Marco technician.

12. information for users in the european community

Pursuant to European Directive 2012/19/EU on electrical waste (WEEE), users in the European community 
are advised of the following.

•  The symbol with the crossed-out dustbin on the appliance or its packaging indicates that 

at the end of the product’s life cycle, it must be collected separately from other waste.

•  Suitable separate collection of the equipment for subsequent recycling, treatment and 

disposal contributes to preventing possible negative consequences for the environ-
ment and health, and favours the recycling of materials that the unit is made of.

•  In accordance with European Directive 2012/19/EU, abusive disposal of the product 

by the user will result in application of penalties as set forth by local law.

13. general warranty conditions

  1.  The warranty lasts 12 months starting from the date of the invoice.
  2.  for warranty the free substitution of the components of the machine are intended, which have to be 

recognized by la San Marco to have manufacturing defects. The warranty applies only to the original 
components, and it falls in case of the use of unoriginal components or of an the machine itself.

  3.  The warranty doesn’t apply to the substitutions or to the reparations that result by a normal functioning 

usury of the device, from deterioration or accidents provoked by a negligence or carelessness in the use.

  4.  The electric parts, and all the parts that result to be defective because of damage linked to transport, 

wrong installation, bad maintenance operated by non authorized staff, by the missing or improper use of 
the water softener system or the water entrance filler, by the improper use  of the machine or a different 
use from the one the machine was built for or, lastly, by circumstances that can’t be attributed to manu-
facturing defects.

  5.  The labour and the technical interventions linked to the installation of the machine, the parts subjected 

to normal usury and all the consuming material are excluded from the warranty service.

  6.  The components are covered by the warranty only if they are rendered complete in all their parts, they must 

not result to be altered and the manufacturing defects mustn’t be cancelled, removed or made illegible.

  7.  The substitution of the machine and the extension of the warranty is excluded after a malfunction oc-

curred. The reparation, change or substitution of the pieces during the warranty period can’t have the ef-
fect to extend the warranty period. All the actions and claims are excluded from the warranty’s coverage, 
especially those that tend to the reparation of the direct or indirect damage caused by people or other 
objects that are different from the delivered products, and also the refund of the eventual missed profits.

  8.  la San Marco S.p.A declines every responsibility for eventual damage that could derive, directly or indi-

rectly to people, animals of things as a consequence of the missing observance  of all the prescriptions 
indicated in the user manual that accompanies every product and concerning, especially, the warnings 
about the installation, use and maintenance of the machine.

  9.  The warranty concerns  the free substitution of the defective pieces with the relative free dispatch  of the 

pieces of substitution to the buyer; the warranty doesn’t cover the labour. The dispatch of the defective 
pieces to the supplier is charged to the buyer. 

10.  Every returned component of which the substitution covered by the warranty is asked for, has to be 

agreed with the client and approved by the commercial office of la San Marco to be accepted. 

11.  la San Marco S.p.A declines every responsibility for eventual damage caused, directly or indirectly, from 

the improper use of the machine, from the wrong installation or bad maintenance, excluding what explic-
itly previewed by the law.

Summary of Contents for 100 E SPRINT 10L

























Reviews: