La Crosse WM9280 Meteotime User Manual Download

Page: 34 / 42

2.7 WIRELESS OUTDOOR RAIN GAUGE

The main unit records the total amount of rainfall for the last hour, last 24 hours, yesterday, last week and last month.

The rainfall may be displayed in mm or inches. A daily rainfall alert function is available which can be programmed to

sound if the daily rainfall exceeds a pre-configured limit.

ACCESSING RAIN GAUGE READING

From the main console unit, press [

▲

] or [

▼

] until the RAIN icon on the display starts flashing.

VIEWING RAIN STATISTICS

Each press of [SET] or [MEMORY] rotates display between different rain statistics:

• Last hour

• Last 24 hour

• Yesterday

• Last week

• Last month

Tip: For an estimation of the rain rate, the Last Hour Rainfall value can be understood as “inch/hr” or “mm/hr”.

RESETTING THE RAINFALL STATISTICS MEMORY

Press and hold [MEMORY] to reset all rainfall statistics.

SETTING UNITS FOR RAIN DISPLAY (INCH OR MM)

Press and hold [SET] to convert units between mm and inches.

ACTIVATING/DESACTIVATING THE DAILY RAINFALL ALERT

1. Each press of [ALARM/CHART] rotates display between the current rainfall statistics and the daily rainfall alert

(“ALARM HI” will be displayed).

If the alert is desactivated, “OFF” will be shown, otherwise the rainfall alert value is shown.

2. When the rainfall alert is displayed, pressing [

▲

] or [

▼

] will activate/desactivate it.

SETTING UP THE DAILY RAINFALL ALERT

1. Press [ALARM/CHART] to display rainfall alert.

2. Press and hold [ALARM/CHART] until rainfall alert and “ALARM HI” starts flashing in the display.

3. Set value for rainfall alert:

Press [

▲

] or [

▼

] to adjust value. Press and hold either button for fast advance. Press [ALARM/CHART] to confirm your

selection.

4. Upon completion the display will be returned to the rainfall alert display.

DISABLING WHEN DAILY RAINFALL ALERT IS ACTIVATED

Press [ALARM/CHART] to disable the rainfall alert.

Summary of Contents for WM9280 Meteotime











































Search results

Summary of Contents for WM9280 Meteotime

Reviews:

Related manuals for WM9280 Meteotime

Brands by name

Popular brands

La Crosse WM9280 Meteotime, User Manual

Search results

Summary of Contents for WM9280 Meteotime

Reviews:

Related manuals for WM9280 Meteotime

Brands by name

Popular brands