temperature station receives the temperature signal,
you will need to follow the battery installation
procedure again.
To complete the set up of your wireless temperature
station after the 15 minutes have passed please
follow the steps that follow in the Detailed Set-Up
Guide.
DETAILED SET-UP GUIDE
I. BATTERY INSTALLATION
A. REMOTE TEMPERATURE SENSOR
1. Remove the mounting
bracket. The bracket
snaps on and off easily.
2. R e m ove t h e b a t t e r y
cover, by sliding the
cover down.
3. Observing the correct
polar ity install 2 AA
batteries. The batteries
will fit tightly (to avoid
start-up problems make
sure they do not spring
free).
4. Replace the battery cover by sliding upwards.
Be sure battery cover is on securely.
B. INDOOR TEMPERATURE STATION
1. R e m ove t h e b a t t e r y
cover. To do this, insert
a solid object in the
space provided at the
lower-central position of
the battery cover, then
push up and pull out on
the battery cover.
2. Observe the correct polarity, and install 2 AA
batteries.
3. Replace the battery cover.
Note:
Immediately after the batteries have been
installed, the LCD (Liquid Crystal Display) will flash,
and a tone will sound. Within a few seconds the
indoor temperature and indoor relative humidity will
be displayed. If not, remove batteries for 10 seconds
and reinstall. If the outdoor temperature is not
displayed within four minutes, remove batteries from
both units, wait 10 seconds, and reinstall making
sure to install batteries into the remote temperature
sensor first. The time will show -:— and start
searching for the signal. If it successfully receives
the time signal (usually at night), it will display the
correct time (default time-zone is Eastern). You will
need to adjust the time zone to match your local
time.
PROGRAM MODE
Programming Note: If 30 seconds is allowed to pass,
or the CH button is pressed during the programming
mode, the unit will confirm/set the last information
entered-the display will stop flashing and return to
normal time-date readings. If you don’t leave the
program mode during the programming of sections
III through XII, you can advance to step 4 of the
next program setting. If you do leave the program
setting (or want to program a specific setting) follow
each instructional step to program that setting.
I. PROGRAMMING SEQUENCE AND DEFAULT
SETTINGS
The programming sequence and default (factory)
settings are as follows:
LCD Contrast
5
Time Zone
-5 (Eastern)
Daylight Saving Time
1 (on)
Radio-controlled time reception ON
12/24-hour time
12
Time
12:00
Year
2003
Day and Month
1.1.
Snooze (this function not used) 10
Temperature Format
˚F
Setting the forecast sensitivity
(this function not used)
2
Please note that while there is a snooze adjustment
in the programming this is an unused function as
there is no alarm on the indoor temperature station.
II. FUNCTION KEYS
The function keys are located on the front of the
unit directly below the LCD.
III. SETTING THE LCD CONTRAST
1. Press and hold the SET button for 5 seconds.
2. “LCD” will show in the time LCD and the number
setting will flash.
Note:
There are 8 LCD contrast levels to choose
from-”Lcd 0" is the lightest, and “Lcd 7” is the darkest.
3. Press and release the IN button to select the level
you desire.
4. Press and release the SET button to confirm and
advance to the Time Zone setting.
IV. TIME ZONE SETTING
1. Press and hold the SET button for 5 seconds.
2. “LCD” will show in the time LCD and the number
setting will flash.
3. Press and release the SET button again.
4. The time zone will flash in the date LCD.
5. Press and release the IN button to select your
time zone.
Note:
When a time zone for the U.S. is selected the
corresponding abbreviation will appear above the
time (please see the table on the next page). It is
possible to select any time zone from -12 GMT to
+12 GMT (for example to see the time in another
country)
SIZE AA LR6
SIZE AA LR6
Temp. Transmitter
433 MHz
Battery
Cover
+
SIZE AA LR6
+
SIZE AA LR6
Battery
Cover
IN
CH
SET
OUT
TIME EST
DST
GB
P.8
GB
P.9
GB
P.6
GB
P.7
