background image

La Crosse Technology, Ltd.  

Page 8 

 

Does the Clock Have a Backlight? 

 

  No, this Digital Atomic Clock does not have a backlight.   

  Generally, an a/c power cord is required for products to have a backlight. 

  This clock does not use a/c power cord. 

 

Dashes, OFL or Stuck Indoor Temperature 

 

  This is generally a power related issues.  

 

Batteries

 may be overpowered or underpowered. Remove batteries from Digital Atomic 

Clock.  

  Press any button 20 times. Leave the Digital Atomic Clock unpowered for 1-2 hours.  

  Insert fresh alkaline batteries with correct polarity.  

  If the indoor Temperature is still dashes or OFL, the Digital Atomic Clock may need 

replacement. 

 

Inaccurate Indoor Temperature Reading 

 

 

Side-by-side test

: Bring the outdoor transmitter in the house and place it next to the Digital 

Atomic Clock for 2 hours.  

  Compare indoor and outdoor Temperature. The temperature should be within 4 degrees to 

be within tolerance.  See the section on 

accuracy

 for details. 

  Look for heat sources such as sunlight, door or window frames, or reflected heat of cold. 

 

Time is off by hours 

 

  Check to see if the 

WWVB

 Tower icon appears on the Digital Atomic Clock. If not, the Digital 

Atomic Clock has not received a WWVB time signal in the past 24-hours.  

  Reposition the Digital Atomic Clock with the front or back facing Colorado. 

  Check that the 

Time Zone

 selected correctly reflects your location.  Adjust the time zone in 

the 

Program Menu

  Check that the DST indicator is correct for your location (most areas observe DST so this 

should be ON). Adjust the DST indicator in the 

Program Menu.

 

  Large buildings, metal roofed buildings and buildings or rooms full of electrical and/or radio 

equipment make it difficult to receive the WWVB time signal. 

 

Daylight Saving Time 

 

 

Dependent on your location, position of the clock in your home, and atmospheric 
interference, it may take up to 5 nights for the change from Daylight Savings Time to 
Standard Time and vice-versa to occur.

 

  Check for a 

WWVB

 Tower Icon showing on your Clock. The tower icon indicates you have 

received the WWVB signal from Ft Collins CO in the past 24-hours.  

  Check that the clock is in the correct 

Time Zone

.  

  Check whether the DST indicator is ON or OFF. If the indicator is OFF the clock will not 

change. 

  Check for fresh 

batteries

. Without proper batteries, the antenna will have a harder time 

picking up the signal.

 

  Position the Digital Atomic Clock in a window (

with the front or back

) facing Ft. Collins, 

Colorado and leave for up to five nights. If you do not have a window facing this direction, 
locate the Clock near an outside wall and point the unit in this general direction.  

 
 
 

Summary of Contents for 513-149V2












Reviews: