- Carefully pull the light bulb socket
downward.
- Remove and replace the bulb.
- Reassemble.
Interior lights and destination
marker:
- Pull the eight roof ventilators off
the model.
- Remove eight screws underneath
the roof ventilators (Fig. 3/4).
- Pull the roof upward and off the
model.
- Remove the circuit board.
- Remove and replace the bulb.
- Reassemble.
Maintenance parts
50010 Smoke and Cleaning Fluid
50019 Maintenance Oil
51020 Gear Lubricant
62201 Standard Motor with Short
Shaft
63110 Brushes with Springs,
4 sets (2 packages needed)
63218 Pick-Up Shoes, 2 pieces
(2 packages needed)
68511 Plug-In Bulb, Clear, 5V,
10 pieces
INSTRUCTIONS FOR ADVANCED
USERS
MTS Onboard Decoder
Programming functions
You can program numerous func-
tions of the onboard decoder to suit
your requirements. If you want to do
this, program the “function values”
in “registers” (CVs) using a PC and
the 55045 MTS PC Decoder
Programming Module. You can also
program the function values using a
55015 Universal Remote.
Hints:
- For normal operation, it is not nec-
essary to change the function val-
ues.
- If programming results in unsatis-
factory operation, you can repro-
gram the factory pre-set values of
most important CVs: Program reg-
ister CV55 to function value 55.
This also reprograms the loco
address to the factory pre-set
value.
To reprogram the factory pre-set
function values with the 55015 (dis-
plays shows “P --”) input 6, 5, and 5
and press the right arrow button. The
display shows “P --” again: Input 5,
5, and 5 and press the right arrow
button again.
When operating with the Multi-Train
System, the streetcar features a
“Back-EMF” function. This keeps the
motor speed constant (and under
normal conditions the model’s
speed), even when the load of the
model changes, for example, in
curves or on grades. This feature
does not work at top speed, because
additional voltage must be available
to overcome any added load.
If desired, numerous functions of the
onboard decoder, such as accelera-
tion, braking, direction of travel and
many others, can be programmed
using a PC and the 55045 MTS PC
Decoder Programming Module (see
Instructions for advanced users
).
These functions also can be pro-
grammed from the 55015 Universal
Remote.
Doors
To open the doors, fold down the
step underneath the doors (Fig. 5/6).
Then the doors open. To close the
doors, fold up the step.
Inserting LGB figures
Remove the roof (see
Replacing the
light bulbs: interior lights
) to insert
additional LGB figures. The figures
may need modification to fit onto the
seats.
Lighting
This model features directional light-
ing.
Power Supply
Attention!
For safety and reliability,
operate this model with LGB power
supplies (transformers, power packs
and controls) only. The use of non-
LGB power supplies will void your
warranty.
Use this model with LGB power sup-
plies
with an output of more than 1
amp.
For more information on LGB
power supplies for indoor, outdoor
and multi-train operation, see the
LGB catalog.
Attention!
After extended operation,
this model may leave carbon dust or
other debris around the track. This
dust and debris can stain carpet and
other materials. Consider this when
setting up your layout. Ernst Paul
Lehmann Patentwerk and LGB of
America are not liable for any dam-
ages.
SERVICE
Do-It-Yourself Service Levels
Level
- Beginner
Level
- Intermediate
Level
- Advanced
Attention!
Improper service will void
your warranty. For quality service,
contact your authorized retailer or an
LGB factory service station (see
Authorized Service
).
Hint:
Additional expert instructions
for many LGB products are available
at www.lgb.com.
Lubrication
The axle bearings should be lubricat-
ed occasionally with a small amount
of LGB Maintenance Oil (50019).
Cleaning 1
This model can be cleaned externally
using a mild detergent and gentle
stream of water. Do not immerse this
model.
Replacing the light bulbs
Front lights:
- Turn the model upside down and
lay it on a soft surface.
- Remove two screws on the plate
with the pilot.
- Remove the plate.
13
12