background image

Natural 

Gas

Congratulations!

You have purchased the finest convection heater available. 

Your new L.B. White heater incorporates the benefits from the most experienced

manufacturer of heating products using state-of-the-art technology.

We, at L.B. White, 

thank you

for your confidence in our products and 

welcome any suggestions or comments you may have...call us, toll-free, 

at (800) 345-7200.

Owner's Manual and Instructions

“Workman” Convection Construction Heaters

View this manual online at www.lbwhite.com

ATTENTION ALL USERS

This heater has been tested and evaluated by C.S.A. International in accordance

with Standard ANSI Z83.7

CSA 2.14 and is listed and approved as a direct fired

vertical convection construction heater for use on combustible floors.  This heater

is intended for use as a portable, temporary heater for buildings under

construction, alteration, or repair.  If you are considering using this product for any

application other than its intended use, then please contact your fuel gas supplier,

or the L.B. White Co., Inc.

MODELS

OUTPUT 

(Btuh)

FUEL

CV100N

100,000

Certification by:

SCAN THIS QR CODE

with your smartphone or 
visit http://goo.gl/nvneR
to view maintenance
videos for L.B.White heaters.*

*Requires an app like QR Droid for Android or 
QR Reader for iPhone.

150-29466 REV.B 

Summary of Contents for Workman 100 Plus



















Reviews: