background image

Natural gas has a  man-made odorant added specifically for detection of fuel gas leaks.

If a gas leak occurs, you should be able to smell the fuel gas.  

THAT’S  YOUR  SIGNAL  TO  GO  INTO  IMMEDIATE  ACTION!

Do not take any action that could ignite the fuel gas.  Do
not operate any electrical switches.  Do not pull any
power supply or extension cords.  Do not light matches
o r   a ny   ot h e r   s o u rc e   o f   f l a m e .     D o   n ot   u s e   yo u r
telephone.

Get everyone out of the building and away from the area
immediately.

Close all fuel supply valves or the main fuel supply valve
located at the meter.

Natural gas is lighter than air and can collect around
rafters or ceilings.

Use your neighbor’s phone and call your fuel gas 

supplier and your fire department.  Do not re-enter the
building or area.

Stay out of the building and away from the area until
declared safe by the firefighters and your fuel gas 

supplier.

FINALLY,  let the fuel gas ser vice person and the
firefighters check for escaped gas.  Have them air out
the building and area before you return.  Properly
trained service people must repair the leak, check for
further leakages, and then relight the appliance for you.

WARNING

Do not use this heater for heating human living
quarters.

Do not use in unventilated areas.

The flow of combustion and ventilation air must not be
obstructed.

Proper ventilation air must be provided to support the
combustion air requirements of the heater being used.

Lack of proper ventilation air will lead to improper
combustion.

Improper combustion can lead to carbon monoxide
poisoning leading to serious injury or death.  Symptoms
of carbon monoxide poisoning can include headaches,
dizziness and difficulty in breathing.

Proper ventilation air for combustion must be provided
in accordance with OSHA 29 CFR 1926.154, Temporary
Heating Device, ANSI A10.10, Safety Requirements for
Temporary and Portable Space Heating Devices, or the
Natural Gas and Propane Installation Code, CAN/CSA
B149.1 as appropriate. 

Asphyxiation Hazard

Some people cannot smell well.  Some people cannot
smell the odor of the man-made chemical added to
natural gas.  You must determine if you can smell the
odorant in this fuel gas.  

Learn to recognize the odor of natural gas.  Your local
natural gas supplier (utility) will be more than happy to
give you a “scratch and sniff” pamphlet.  Use it to
become familiar with the fuel gas odor.  

Smoking can decrease your ability to smell.  Being
around an odor for a period of time can affect your
sensitivity to that particular odor.

The odorant in natural gas is colorless and the intensity
of its odor can fade under some circumstances.

If there is an underground leak, the movement of gas
through the soil can filter the odorant.  

Always be sensitive to the slightest gas odor. If you
continue to detect any gas odor, no matter how small,
treat it as a serious leak.  Immediately go into action as
discussed previously.

5

Safety Precautions

FUEL GAS ODOR

ODOR FADING -- NO ODOR DETECTED

ATTENTION -- CRITICAL POINTS TO REMEMBER!

Natural gas has a distinctive odor.  Learn to recognize
this odor.  (Reference “Fuel Gas Odor” and “Odor
Fading” sections above.

If you have not been properly trained in repair and service
of natural gas fueled heaters, then do not attempt to light
heater, per form ser vice or repair s, or make any
adjustments to the heater on the natural gas fuel system.

Even if you are not properly trained in the service and
repair of the heater, ALWAYS be consciously aware of
the odors of propane gas and natural gas.

A periodic sniff test around the heater or at the heater’s
joints; i.e. hose, connections, etc., is a good safety
practice under any conditions.  If you smell even a small
amount of gas, CONTACT YOUR FUEL GAS SUPPLIER
IMMEDIATELY.  DO NOT WAIT!

Summary of Contents for Workman 100 Plus



















Reviews: