background image

Propane Vapor

Withdrawal

or

Natural Gas

Congratulations!

You have purchased the finest portable forced air construction heater available. 

Your new L.B. White heater incorporates the benefits from the most experienced

manufacturer of heating products using state-of-the-art technology.

We, at L.B. White, 

thank you

for your confidence in our products and 

welcome any suggestions or comments you may have...call us, toll-free, 

at (800) 345-7200.

Owner's Manual and Instructions

Tradesman Construction Heaters

ATTENTION ALL USERS

This heater has been tested and evaluated by C.S.A. International in accordance with

the requirements of Standard ANSI Z83.7

CSA 2.14 and is listed and approved as a

direct gas-fired forced-air construction heater with application for the temporary

heating of buildings under construction, alteration, or repair.  If you are considering

using this product for any application other than its intended use, then please

contact your fuel gas supplier, or the L.B. White Co., Inc.

MODELS

OUTPUT 

(Btuh)

FUEL

CP155               

155,000

Certification by:

150-22331-B

Rev. 4-21-08

Summary of Contents for CP155
































Reviews: