background image

WARNING

Fire and Explosion Hazard

Not for home or recreational vehicle use.

Installation of this heater in a home or

recreational vehicle may result in a fire or

explosion.

Fire or explosions can cause property

damage or loss of life.

FOR YOUR SAFETY

If you smell gas:

1. Open windows.

2. Don't touch electrical switches.

3. Extinguish any open flame.

4. Immediately call your gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other

flammable vapors, liquids, or materials  in

the vicinity of this or any other appliance.

WARNING

Fire and Explosion Hazard

Do not modify this appliance.

Keep solid combustibles a safe distance

 

away from the appliance.

Solid combustibles include wood or paper

 

products, feathers, straw, and dust.

Do not place articles against this appliance.

Do not spray aerosols in the vicinity of this

 

appliance while it is in operation.

Do not use the appliance in spaces which

 

contain or may contain volatile or airborne

 

combustibles, or aerosols.

Failure to follow these instructions may

 

result in a fire or explosion.

Fire or explosions can lead to property

 

damage, personal injury or loss of life.

Do not use or store flammable materials in 

or near this appliance.

GENERAL  HAZARD  WARNING

Failure to comply with the precautions and instructions provided with this heater, can result

in:
— Death

— Serious bodily injury or burns

— Property damage or loss from fire or explosion

— Asphyxiation due to lack of adequate air supply or carbon monoxide poisoning 

— Electrical shock

This heater is approved for industrial use only

Read this Owner’s Manual before installing or using this product.

Only authorized service people shall repair or install this heater.

Save this Owner’s Manual for future use and reference.

Owner’s Manuals and replacement labels are available at no charge.  For assistance, contact

L.

B. White at +1-608-783-5691.

WARNING 

Proper gas supply pressure must be provided to the inlet of the heater.

Refer to rating plate for proper gas supply pressure.

Gas pressure in excess of the maximum inlet pressure specified at the heater inlet can cause

fires or explosions.

Fires or explosions can lead to serious injury, death, building damage or loss of livestock.

Gas pressure below the minimum inlet pressure specified at the heater inlet may cause

improper combustion.

Improper combustion can lead to asphyxiation or carbon monoxide poisoning and therefore

serious injury or death to humans and livestock.

2

Summary of Contents for AD100





























Reviews: