background image

Propane Vapor

Withdrawal

Congratulations!

You have purchased the finest heater available. 

Your new L.B. White heater incorporates the benefits from the most experienced
manufacturer of heating products using state-of-the-art technology.

We, at L.B. White, 

thank you

for your confidence in our products and 

welcome any suggestions or comments you may have...call us, toll-free, 
at 1-800-345-7200.

Owner's Manual and Instructions

Construction Heaters

Certification by:

150-23363

MODELS

OUTPUT 

(Btuh)

FUEL

346JX

60,000

L.B.WH

WHITE

ITE

W6636 L. B. White Rd., Onalaska, WI 54650

(800) 345-7200

(608) 783-5691 

Fax (608) 783-6115

®

ATTENTION ALL USERS

This heater has been tested and evaluated by C.S.A. International in accordance
with Standard ANSI Z83.7

z

CSA 2.14 and is listed and approved as a direct gas-fired

circulating construction heater with intended use for primarily the temporary heating
of buildings under construction, alteration, or repair.  As an alternative use, this
heater has also been tested and evaluated by the L.B. White Co., Inc. for the heating
of agricultural animal confinement buildings and has been used in such
applications for many years.  If you are considering using this product for any
applications other than those previously stated, then please contact your fuel gas
supplier or the L.B. White Co., Inc.

Summary of Contents for 346JX



























Reviews: