L-Acoustics K2 WST Rigging Manual Download

Page: 10 / 34

K2 WST

enclosure

RIGGING MANUAL

VERSION 3.0

K2_RM_EN_3.0

w w w . l - a c o u s t i c s . c o m

1 0 / 76

RIGGING SYSTEM DESCRIPTION

K2 enclosures can be ground-stacked and flown independently (K2-BUMP) or in combination with K1 system elements

(K1, K1-SB, or K1-BUMP).

The K2-BUMP is designed to be directly compatible with K1 and K1-SB. The K2 enclosure rigging system requires the

K2-LINK interface to be compatible with the K1 rigging system.

3.1

Elements for enclosure rigging

On both sides, the K2 enclosure integrates two arms to connect to another element of the rigging system, such as an
enclosure or to a flying frame.



At the front, a rotating arm provides a fixed point around which the enclosure can freely rotate until its
connection at the rear.



At the rear, a sliding arm allows the inter-element angle setting and the inter-element rear connection.

The angles between adjacent enclosures are secured by an automatic system that is activated in advance and locks itself
during the stacking and lifting procedures.

Summary of Contents for K2 WST



































Search results

Summary of Contents for K2 WST

Reviews:

Related manuals for K2 WST

Brands by name

Popular brands

L-Acoustics K2 WST, Rigging Manual

Search results

Summary of Contents for K2 WST

Reviews:

Related manuals for K2 WST

Brands by name

Popular brands