KYMCO Scout 50 Service Manual Download Page 1

ZX / SCOUT 
50 

PREFACE 

 
 

This Service Manual describes the technical feature.s and servicing 
procedures for the KYMCO 

ZX / SCOUT 50

.

 

 
In this manual, many illustrations and drawings are used to help 
servicemen have better understanding. 

Section 2 contains the service precautions for all operations and 
troubleshooting stated in this manual.  Read them carefully before starting 
any operation. 
 
Section 3 describes the inspection/adjustment procedures, safety rules and 
service information for each part, starting from periodic maintenance. 
 
Sections 4 through 16 give instructions for disassembly, assembly and 
inspection of lubrication system, engine, fuel system and electrical 
equipment. 
 
Section 17 is the maintenance and inspection directions for the evaporative/ 
exhaust emission control system.  Most sections start with an assembly or 
system illustration and troubleshooting for the section.  The subsequent 
pages give detailed procedures for the section.

 

KWANG YANG MOTOR CO., LTD.

 

OVERSEAS SALES DEPARTMENT

 

OVERSEAS SERVICE SECTION

MARCH 2000

 

 

Summary of Contents for Scout 50





























































































































































































Reviews: