manualshive.com logo in svg

KYLAND Technology SICOM3010G, Hardware Installation Manual

Share
Download
KYLAND Technology SICOM3010G Hardware Installation Manual Download Page 26

                                                SICOM3010G  User’s Manual-v1.0 

25 

 

7 

Reset Button

 

Reset button supports reboot and restoring default configuration. 

Push the reset button and hold for one second then release  to reboot  the 

switch.   

Hold the reset button down for five seconds then release to restore default 

configuration  (including IP address)  and reboot;  the default IP address is 

192.168.0.2

.   

Note

:

 

Don’t hold the reset button down for more than 5  second to avoid restoring 

default configuration. 

8  Management Access 

Access the switch by one of the following three ways. 

8.1  Connected through Console Port 

1. Install the driver for Mini USB onto your PC. The driver “Mini USB 

driver.exe” is in the software download folder, which is on the supplied 

CD. 

2. Use the Console cable that is equipped with Mini USB connector at one 

end and USB connector at the other end to connect the Console interface 

on the switch with the USB port on PC.   

3. On Windows desktop, click Start 

→ All programs → Accessori

es 

→ 

Communications 

→ Hyper Terminal. 

 

Summary of Contents for SICOM3010G

































Reviews:

No comments

Brands by name

Popular brands

Load more brands