Kwikset SmartCode 913 User Manual Download Page 4 | Manualshive

Page: 4 / 15

background image

©2015 Spectrum Brands, Inc.

1. Keep door open. Press the Program button once. The keypad will fl ash

green and you will hear three beeps.

2. Press Lock button once.

3. Enter Mastercode.

4. Press Lock button once.

5. Enter user code to be deleted.

6. Press Lock button once.

7. Re-enter user code to be deleted.

8. Press Lock button once.

Procedure continued on next page

61920 / 01

4 / 15

Technical Support
1-800-327-5625
www.kwikset.com

D

Deleting a Single User Code with the Mastercode Enabled

«
...
2
3
4
5
6
...
»

Summary of Contents for SmartCode 913
















Reviews:

No comments

Related manuals for SmartCode 913

Brand: Falcon Pages: 56

Brand: Waferlock Pages: 11

Brand: Waferlock Pages: 3

TOUCHLOCK BT BL0509

Brand: BIO-key Pages: 9

Brand: I.H.T Pages: 8

Brand: August Pages: 9

Brand: Corbin Russwin Pages: 24

Brand: AAT Pages: 8

Brand: Olympus Lock Pages: 2

Adhesive Magnet Lock

Brand: Qdos Pages: 12

Brand: Ammo doors Pages: 2

PRIME OFFICE 2170

Brand: G-U Pages: 40

Real Living YRD240

Brand: Yale Pages: 20

YD-01-CON-ZW-CH

Brand: Yale Pages: 32

Brand: KAP Pages: 9

Brand: Roger Pages: 2

Brand: KF-LOCK Pages: 3

Brand: Stock Loks Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands