Kval 990FX Page 38 Operation Manual Download

Page: 38 / 96

Description of User Interface Screens

KVAL 990-FX Operation Manual

2-8

Description of User Interface Screens

This section describes the user interface screens. The user interface allows the operator to use a

touch screen to control the door cutting process, auto-run, manually run the door, store door pro

files, and use diagnostics to help troubleshoot the

990-FX

Screen Selection Menu Map

Below are the menu selections for the

990-FX

Note:

Screen layouts may differ due to options that were ordered with the machine.

FIGURE 2-1.

990-FX Menu Map

Main Menu:

Opening Screen. Set Presets to

machine the doors.

See “About the Main Screen” on page 2-10.

Manual Menu:

Control the machine manually

through this screen.

See “About Manual Operation” on page 2-17.

Setup Screen:

Calibrate the position of the

lock location.

See “About the Setup Screen” on page 2-21.

Diagnostic Screen:

Observe the history of the

machine operations. Error messages can be

seen here for troubleshooting.

See “Diagnostic Screen” on page 2-27.

RTS-FX: Option

Summary of Contents for 990FX

































































































Search results

Summary of Contents for 990FX

Reviews:

Related manuals for 990FX

Brands by name

Popular brands

Kval 990FX, Operation Manual

Search results

Summary of Contents for 990FX

Reviews:

Related manuals for 990FX

Brands by name

Popular brands