Kval 990FX Page 84 Operation Manual Download

Page: 84 / 96

About the Electrical Panels

KVAL 990-FX Operation Manual

3-26

About the Electrical Panels

Warning:

High Voltage is present in this panel at the top of the Three Phase Input even with the

disconnect off. If working on the panel, follow safety protocol as described in Chapter 1.
The

990-FX

includes a Main Electrical Panel and a High Frequency Panel. The figures in this sec

tion provide and overview of the location of assemblies in the panels.

Note:

Component layout in the Panels may vary. Essentially the operation is the same.

Note:

Some Options may include a

Main Power Distribution Panel

. This panel accepts factory

power and distributes to the

Main Electrical Panel

and the

High Frequency Panel

. See

your machine schematics tor more information.

Main Electrical Panel

The Main Electrical Panel:

• Supplies voltages to the machine
• Contains the PLC (Programmable Logic Controller)
• Contains servo drives to interact with the servo motors (Axis and Lock Location) in

the front and back sections

FIGURE3- 18.

Main Electrical Box Overview

PLC with Inputs /Outputs
Ethernet Dist. Block

Power Supplies

24VDC and 120Vac Terminal Block

High Voltage Section

• Disconnect
• PDR
• Fuses

Servo Drive

•  Lock Carriage
•  Option: Infeed Shift
•  Option Outfeed Shift

Control Transformer

Summary of Contents for 990FX

































































































Search results

Summary of Contents for 990FX

Reviews:

Related manuals for 990FX

Brands by name

Popular brands

Kval 990FX, Operation Manual

Search results

Summary of Contents for 990FX

Reviews:

Related manuals for 990FX

Brands by name

Popular brands