Kval 990FX Page 57 Operation Manual Download

Page: 57 / 96

Diagnostic Screen

2-27

KVAL 990-FX Operation Manual

Diagnostic Screen

The Diagnostic screen displays all the tasks the

990-FX

performs. This screen can help with trou

ble shooting by associating the error code to machine sections or functions. The top line will have

the most current routine that is running. If the machine issue can not be resolved, call KVAL Inc.

(1-800-553-5825). Have any error code that is displayed, ready to give the KVAL representative.

This will aid in troubleshooting and shorten down time.
The Diagnostic screen keeps track of the all the doors processed on the machine. The quantity is

displayed in the

Total Door Count

box.

To keep track of daily production, the quantity of doors produced in a day is displayed in the

Daily

Door Count

box. This count can be reset with the

Reset Count

button.

FIGURE 2-5.

Diagnostic Screen

Summary of Contents for 990FX

































































































Search results

Summary of Contents for 990FX

Reviews:

Related manuals for 990FX

Brands by name

Popular brands

Kval 990FX, Operation Manual

Search results

Summary of Contents for 990FX

Reviews:

Related manuals for 990FX

Brands by name

Popular brands