Kuzma XL DC Instruction Manual Download Page 10

 

10 

Setting up the turntable: 

 
Tonearm mounting:

 

Ensure that the supporting stand is completely  horizontal.    
  Mount  the    chosen  tonearm  according  to  instructions.  Position  the  tonearm  tower  at  the 
correct distance from the spindle. Firmly secure the armbase onto the tonearm top brass plate  
with two screws, using  Allen key 3mm,  at the side of the tower.  See Fig.11 
 

 

Fig. 11. Fixing screws on top of the tonearm tower. 
 
Raise  the  tonearm  to  an    appropriate  height  above  the  platter.    Position  the  tonearm  cable 
towards the back of the turntable towards the phono input.  Check the length. 
Check  again  the    spindle  to  tonearm  distance  and  rotate  the  tower  to  be  in  an    optimal 
operating position. 

Note: 

When the  Air Line tangential tonearm is used,  additional fine horizontal adjustment of 

the turntable or turntable support is mandatory. 

 
VTA Gauge:  

Hang the digital  display  on the front  of the  tonearm tower using the lever and screw at  the 
bottom of the tower.  
  Ensure that the display does not touch the platter or motor towers. Fig. 8. 
The display can be left  in the 'ON' position for up to three years (battery).  Pressing 'origin' 
will cause 0.00 mm to show.  Switching to + or – will cause this sign to appear in front of the 
numbers.  Pressing  (press  and  hold  for  about  one  sec)  to  'origin'  again,  resets    the  display  to 
zero.  Due to the  limits of  height measurement (12mm), the display should show the middle 
of  the  measurement.    An  appropriate  starting  height  for  the  tonearm  is  when  the  tube  is 
parallel to the record after the  cartridge is mounted. 
 

Setting the VTA  gauge

With Allen key 1.5mm  release the small  brass  weight  which holds the display in  the upper 
position.  The display will show minimum.  Reset and the measurement will show zero. Lift 
the  vertical  rod  for  about  6-7mm  (middle  position)  and  with  Allen  key,  secure  this  position 
with the screw on the brass weight.  Then again reset and it will show that this new position is 
zero. 
  
 

Summary of Contents for XL DC














Reviews: