background image

20

All Kurt Manufacturing Company industrial workholding products and parts 
with the exceptions noted below, are warranted against  defects in material and 
workmanship for the life of the product or part.  (The life of the product is defined 
as that point in time when such item no longer functions due to normal wear and 
tear.)   Failure to properly maintain and/or properly operate the product or part that 
has been worn out, abused heated ground or otherwise altered, used for a purpose 
other than that for which it was intended, or used in a manner in consistent with 
any instructions regarding its use.  The sole obligation of Kurt Manufacturing 
Company, Inc. (Kurt) and the   purchaser’s SOLE AND EXCLUSIVE REMEDY 
hereunder, shall be limited to the replacement or repair of any Kurt product or 
part (by an authorized Kurt technician) which are returned to Kurt Manufacturing 
Company’s place of business, transportation, shipping and postal charges prepaid, 
and there determined by Kurt Manufacturing Company to be covered by the 
warranty contained herein.

THE LIMITED WARRANTY DESCRIBED HEREIN IS MADE EXPRESSLY IN LIEU OF 
ANY OTHER EXPRESSED OR IMPLIED WARRANTIES, INCLUDING ANY IMPLIED 
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
KURT MANUFACTURING COMPANY IS NOT RESPONSIBLE FOR THE IMPROPER 
USE OF ITS PRODUCTS.  KURT SHALL NOT BE LIABLE FOR ANY DIRECT, 
INDIRECT, INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING 
BUT NOT LIMITED TO, LOSS OF USE, REVENUE OR PROFIT.

KURT ASSUMES NO LIABILITY FOR, AND MAKES NO WARRANTY REGARDING 
ANY PURCHASE ITEMS WHERE THE MANUFACTURER OF SUCH ITEM  EXTENDS 
A SEPARATE WARRANTY.

WARRANTY

Summary of Contents for CROSSOVER ANGLOCK VISE DX6






















Reviews: